Bauer LINESTAR 9000 - Specified Minimum Curve Radius

115 pages

To Next Page

To Previous Page

Operating Manual for BAUER LINESTAR 9000 with hose feed 21

10.2 SPECIFIED MINIMUM CURVE RADIUS

A end tower swivels around main cart

Radius = 2 x SL

Radius min. = 600 m

B main cart swivels around end tower

Radius = 3 x SL

Radius min. = 900 m

Main Page

Default Chapter6
- Table of Contents6
1 General Instructions9
2 Warning Symbols10
3 General11
4 General Instructions for Safety and Accident Prevention11
5 Safety Precautions for Linestar 900012
- Electrical System12
- Mechanical System12
6 Technical Description13
- Components of the Linestar 900013
  - Components of the below Ground Guidance14
- Centre Feed - End Feed16
  - Centre Feed16
  - End Feed16
7 Use of Linestar17
- General Limits17
  - Inclination17
  - Permissible Bending Angles17
- Limits with below Ground Guidance18
  - Limits When Using an Open Conductor Loop18
  - Limits When Using an Open Conductor Loop with Asymmetrical Layout19
- Track Determination and Maintenance20
  - Travel Direction20
8 Linestar Central Unit21
- Four-Wheel Main Cart21
- Two-Wheel Central Unit22
9 Control Centre23
- Control Centre Linestar Pro23
  - Standard Built-In Components24
- Control Centre Linestar Pro-G26
  - Standard Built-In Components27
10 Linear Control System28
- General28
- Specified Minimum Curve Radius29
- Furrow Guidance30
- Cable Guidance Installation and Adjustment30
- Below Ground Guidance32
  - Oscillator Box, Steering Antennas, Track Unit32
  - Below Ground Cable35
- Setting Linear Control36
  - Furrow and Cable Guidance36
  - Below Ground Guidance37
- Setting Stop Switch37
11 Diesel Generator Unit39
12 Alignment of the Linestar39
- Aligning the Central Unit Parallel to the Linear Guidance (Furrow, Cable)39
- Align Spans 90° at Right Angle to the Central Unit40
- Aligning the Central Unit to the Linear Guidance (below Ground Guidance)40
13 Alignment Control42
- Microswitch Adjustment42
14 Electrical System43
- Cables and Markings43
- Installation, Connection of Control Centre44
- Alignment Control Connection44
15 First Start-Up44
- Checking of Central Unit44
- Checking of Truss, End Tower and Overhang45
- Gearboxes and Drive Motors45
  - Gearboxes45
  - Drive Motor46
- Oscillator Box (Only with below Ground Guidance)46
- Control Centre47
  - Checking Voltage and Wiring47
  - Checking Tower Travel Direction47
- Alignment of the Towers48
- Alignment Control Adjustment48
- Checking Alignment49
- Machine Offset from Linear Guidance51
  - Alignment of the Machine with Furrow / Cable Guidance51
  - Ausrichten der Maschine mit Untergrundsteuerung52
16 Terminology54
17 Start-Up55
- Start Linestar in Operating Mode "Linear55
  - Start Linestar with Hose Feed55
- Starting after Intermediate Stop55
- Shut-Down Procedure56
  - System Shut off During Irrigation56
  - Automatic Systemm Shut off at Field End56
- Starting Linestar to Run in Opposite Direction after an Automatic Shut-Down56
- Starting the Linestar in Operating Mode "Wheel Swivelling57
- Starting the Linestar in Operating Mode "Pivoting57
- Shut down Procedure58
18 Maintenance Instructions59
- Service Intervals59
- Service Plan60
- Post-Season Maintenance62
- Pre-Season Maintenance62
  - Preload Forces and Tightening Torques of Bolts63
19 Troubleshooting64
- Restart after Doglegging65
20 Technical Data66
- Dimensions of Bauer Linestar 9000 - 2 Wheel66
- Dimensions of Bauer Linestar 9000 - 4 Wheel One Sided66
- Dimensions of Bauer Linestar 9000 - 4 Wheel Double Sided66
21 Options67
- Low Pressure Shut-Off67
- Electric Shut-Off Valve (Central Unit)67
- End Gun67
- Booster Pump for End Gun67
- Automatic Interval Control68
- Automatic „On/Off" and Interval Control68
- Tower Alignment Switch68
- Running Light68
- End Stop68
- Stop Ramp69
22 Towing of Linestar 2-Wheel69
- Towing the Linestar from Central Unit69
- Towing the Linestar at the End Tower71
- Towing the Linestar at a Freestanding Span72
23 Electrical Wiring Diagrams74
- Control Center Linestar Pro75
  - Control Center Linestar Pro - Wiring Diagram 175
  - Control Centre Linestar Pro - Infeed78
- Control Centre Linestar Pro with below Ground Guidance80
  - Control Centre Linestar Pro W. below Ground Guidance - Wiring Diagram81
  - Control Centre Linestar Pro W. below Ground Guidance - Infeed84
- Control Centre Linestar Pro-G89
  - Control Centre Linestar Pro-G - Wiring Diagram 189
  - Control Centre Linestar Pro-G - Infeed92
- Linestar Linear Control94
- Linestar Tower Box100
- Booster Pump for End Gun110
24 Service - Evidence111
25 Conformity Certificate115

Bauer LINESTAR 9000 - Specified Minimum Curve Radius

Table of Contents

Related product manuals