To Next PageTo Next PageWhy does my Baxi Boiler have loss of flame at ignition?
If you experience a loss of flame at ignition with your Baxi Boiler, check that the flame sensing electrode is in good condition and correctly positioned. Also, ensure the wire is uninterrupted and makes good contact with the flame sensing electrode and the ignition switch. Check for any recirculation of fumes.
What to do if Baxi LUNA DUO-TEC+ Boiler has incorrect power supply frequency?
If your Baxi Boiler has an incorrect power supply frequency, check whether the incorrect electric power supply frequency is due to causes outside the boiler. If so, contact the power supply company.
How to fix communication problem on Baxi LUNA DUO-TEC+?
If your Baxi Boiler displays a 'Communication problem between boiler board and control unit' with a probable short circuit on wiring, check the wiring between the Ambient Unit and the electronic board or RF link.
How to resolve a gas valve control error on Baxi LUNA DUO-TEC+?
If your Baxi Boiler displays 'Gas valve control error', check the connections between the gas valve and the electronic board. If necessary, replace the electronic board.
How to fix safety thermostat intervention in Baxi LUNA DUO-TEC+ Boiler?
If your Baxi Boiler experiences an intervention of safety thermostat for excess temperature in low temperature system, check the correct operation of the pump and the water circulation in the low temperature system. Also, check the pump power input wiring.
What causes Fumes NTC to trip on Baxi Boiler?
If your Baxi Boiler displays 'Fumes NTC tripped due to overtemperature', check the heat exchange level of the water-fumes exchanger for possible insufficient circulation or the presence of scale. Also, check the fumes NTC probe.
How to troubleshoot a fan fault on a Baxi Boiler?
If your Baxi Boiler displays a fan fault, check the correct operation of the fan. Also, ensure that the fan power supply wiring is connected to the electronic board.
What to do if Baxi Boiler shows internal board error?
If your Baxi Boiler displays an 'Internal board error', replace the electronic board.
What to do if the pressure in hydraulic circuit is too low in Baxi Boiler?
If the pressure in the hydraulic circuit of your Baxi Boiler is too low, and the CH circuit pressure is less than 0.5 bar, refill the system. Also, check that the hydraulic pressure switch works correctly.
How to fix a No Flame error on a Baxi Boiler?
If your Baxi Boiler shows 'No Flame', verify that the flame sensing electrode is in good condition and correctly positioned. Also, check the wire is uninterrupted and makes good contact with the flame sensing electrode and the ignition switch. Refer to the actions indicated in E92.
Explains symbols for general warning, burns, high voltage, and freezing hazards.
Explains symbols for important information and generic prohibitions.
Actions for gas smell: switch off, ventilate, contact service.
Actions for combustion fumes: switch off, ventilate, contact service.
Caution against storing flammable materials near the boiler.
Critical instruction to power off boiler before maintenance or cleaning.
Steps for preparing domestic hot water and heating circuits before boiler installation.
Mandate for initial boiler startup by an authorized service engineer.
Advice on setting heating temperatures and using controls for energy efficiency.
Guidance on DHW temperature setting to reduce energy and scale.
Step-by-step guide for the first-time boiler startup.
How to set Central Heating (CH) and Domestic Hot Water (DHW) flow temperatures.
Guide to choosing between DHW, Heating, or DHW & Heating modes.
Recommendations for system protection during winter or prolonged shutdowns.
Explanation of the built-in automatic antifreeze protection for the heating system.
Requirement for professional conversion between natural gas and LPG.
How error codes are displayed and what they signify.
Instructions for users to reset specific faults using the control panel.
Method to access and view internal boiler data and parameters.
Steps to safely turn off the boiler while maintaining anti-freeze protection.
Guide to filling the heating system, checking pressure, and venting air.
Importance and recommendation for annual maintenance by authorized service centers.
Essential instructions and considerations for installers before commencing work.
Guidance on boiler placement, fixing, and connecting water and gas lines.
Details of items supplied with the boiler and connection point identification.
Instructions for installing coaxial air and flue ducts, including bends and lengths.
Guidance for installing separate air and flue ducts using an accessory kit.
Requirements for safe electrical installation, including earthing and power supply.
Details for connecting power, room thermostat, and other basic controls to M1.
Wiring specifications for accessories like remote control, probes, and storage boiler sensors on M2.
Specific steps to wire a room thermostat to the boiler's terminal block.
How to connect and configure an external sensor for climate curve control.
Guidance for connecting external storage boilers and zone heating systems.
Detailed procedure for the first startup, including gas type analysis.
How to use the function to remove air from the heating circuit.
Explanation of the function to run the boiler at maximum power for maintenance.
How to perform a combustion test and expected CO2/O2 values.
Guide to adjusting CO2 levels for optimal combustion efficiency.
Information on the gas valve and the process for gas conversion.
Steps to access, view, and modify boiler parameters.
Overview of essential parameters for initial setup and basic configuration.
Description of advanced parameters for fine-tuning boiler operation.
How to adjust parameter P13 to limit maximum heating output.
Table mapping P13 values to specific kW heating outputs for boiler models.
Details of safety devices like limit thermostat, pressure switch, and flame sensor.
Explanation of pump post-circulation, antifreeze, and anti-block features.
Information on pump flow rate and head characteristics for system matching.
Key checks and controls for annual servicing to ensure efficiency and safety.
Procedure for cleaning the cold water filter within the hydraulic unit.
Correct placement of ignition and flame sensing electrodes for reliable operation.
List of components that necessitate an automatic calibration after replacement.
Step-by-step guide to perform the automatic calibration function after component changes.
Safety measures and requirements for dismantling the appliance by qualified personnel.
Information on the correct and environmentally responsible disposal of the boiler.
Comprehensive table of technical specifications for each boiler model.
Detailed performance metrics including efficiency, pressure limits, and water flow rates.
Information on gas consumption, power requirements, and emissions like NOx.
Classification of the boiler's seasonal space heating and water heating energy efficiency.
Data on electrical power consumption in various operating states.
Specific percentage values for seasonal space heating and water heating energy efficiency.
Overview of the boiler's applications for space heating and domestic hot water.
Summary of energy efficiency classes and annual energy consumption figures.
Information on the sound power level and annual fuel consumption.
General| Model | LUNA DUO-TEC+ |
|---|---|
| Category | Boiler |
| Modulation Range | 1:7 |
| Installation | Wall-mounted |
| ErP Rating Heating | A |
| ErP Rating DHW | A |
| NOx Class | 5 |
| Fuel Type | Natural Gas |
| Warranty | 5 years |
| Type | Condensing Combi Boiler |
| Output Range | 24 kW to 33 kW |
