Bender ISOMETER isoRW425 - Page 10

10 isoRW425_D00052_06_Q_DEEN / 11.2023
ISOMETER® isoRW425
Connection
Connection type ................................. screw-type or push-wire terminal
Screw-type terminals:
Nominal current ...........................................................................≤ 10 A
Tightening torque .........................................0.5…0.6 Nm (5…7 lb-in)
Conductor sizes ..................................................................... AWG 24-12
Stripping length .............................................................................8 mm
Rigid/flexible ...................................................................0.2…2.5 mm²
Flexible with ferrules with/without plastic sleeve ..................................
.......................................................................................0.25…2.5 mm²
Multi-conductor rigid .......................................................0.2…1.5 mm²
Multi-conductor flexible ..................................................0.2…1.5 mm²
Multi-conductor flexible with ferrules without plastic sleeve .................
.......................................................................................0.25…1.5 mm²
Multi-conductor flexible with TWIN ferrules with plastic sleeve .............
.......................................................................................0.25…1.5 mm²
Push-wire terminals:
Nominal current ...........................................................................≤ 10 A
Conductor sizes ..................................................................... AWG 24-14
Stripping length ...........................................................................10 mm
Rigid ................................................................................0.2…2.5 mm²
Flexible without ferrules ................................................0.75…2.5 mm²
Flexible with ferrules with/without plastic sleeve ..................................
.......................................................................................0.25…2.5 mm²
Multi-conductor flexible with TWIN ferrules with plastic sleeve .............
.........................................................................................0.5…1.5 mm²
Opening force ..................................................................................50 N
Test opening, diameter ............................................................... 2.1 mm
Other
Operating mode ...................................................... continous operation
Mounting .............................. cooling slots must be ventilated vertically
Flammability class ....................................................................UL 94V-0
Degree of protection, built-in components (DIN EN 60529) .............IP30
Degree of protection, terminals (DIN EN 60529) ..............................IP20
Anschluss
Anschlussart ...............................................Schraub- oder Federklemme
Schraubklemmen:
Nennstrom ...................................................................................≤ 10 A
Anzugsmoment ............................................0,5…0,6 Nm (5…7 lb-in)
Leitergrößen ......................................................................... AWG 24-12
Abisolierlänge ................................................................................ 8 mm
Starr/flexibel ....................................................................0,2…2,5 mm²
Flexibel mit Aderendhülse mit/ohne Kunststoffhülse .............................
.......................................................................................0,25…2,5 mm²
Mehrleiter starr ................................................................0,2…1,5 mm²
Mehrleiter flexibel ...........................................................0,2…1,5 mm²
Mehrleiter flexibel mit Aderendhülse ohne Kunststoffhülse ...................
.......................................................................................0,25…1,5 mm²
Mehrleiter flexibel mit TWIN Aderendhülse ohne Kunststoffhülse .........
.......................................................................................0,25…1,5 mm²
Federklemmen:
Nennstrom ...................................................................................≤ 10 A
Leitergrößen ......................................................................... AWG 24-14
Abisolierlänge .............................................................................. 10 mm
Starr .................................................................................0,2…2,5 mm²
Flexibel ohne Aderendhülse ...........................................0,75…2,5 mm²
Flexibel mit Aderendhülse mit/ohne Kunststoffhülse .............................
.......................................................................................0,25…2,5 mm²
Mehrleiter flexibel mit TWIN Aderendhülse mit Kunststoffhülse ............
.........................................................................................0,5…1,5 mm²
Öffnungskraft ...................................................................................50 N
Testöffnung, Durchmesser ..........................................................2,1 mm
Sonstiges
Betriebsart ......................................................................... Dauerbetrieb
Einbaulage ..............Kühlschlitze müssen senkrecht durchlüftet werden
Entflammbarkeitsklasse ............................................................UL 94V-0
Schutzart Einbauten (DIN EN 60529) ...............................................IP30
Schutzart Klemmen (DIN EN 60529) ................................................IP20