Bentone B40 MF - Table of Contents

3
Bentone B40 MF/B45-2 MF
General
Table of Contents
Table of Contents _______________________________________________________ 3
1. TECHNICAL DATA
_______________________________________________ 8
1.1 Dimensions B40 ______________________________________________ 8
1.2 Setting of ignition electrodes and brake plate _______ 8
1.3 Dimensions B45-2 ___________________________________________ 9
1.4 Setting of ignition electrodes and brake plate _______ 9
1.5 Dimensions, flange _________________________________________ 10
1.6 Recommended nozzle and pressure _________________ 10
1.7 Oil grades _____________________________________________________ 11
1.9 Nozzle for bio oils, 20-28 bar ___________________________ 12
1.10 Nozzle for fossil oils, 22-28 bar ________________________ 13
1.11 Description B40 MF ______________________________________ 14
1.12 Description B45-2 MF ____________________________________ 16
2. INSTALLATION ___________________________________________________ 18
2.1 Acceptance inspection ___________________________________ 18
2.2 Preparations for installation ______________________________ 18
2.3 Distribution of oil ____________________________________________ 18
2.4 Electrical connection ______________________________________ 19
2.5 Nozzle selection ____________________________________________ 20
2.6 Setting of brake plate and air flow _____________________ 20
2.7 Burner installation __________________________________________ 20
2.8 Burner installation __________________________________________ 21
2.9 Check oil line seals _________________________________________ 21
3. FUNCTION DESCRIPTION ________________________________ 22
3.1 B40 MF 1-stage burner __________________________________ 22
3.2 B45-2 MF 2-stage burner _______________________________ 23
4. BASIC SETTINGS ______________________________________________ 24
4.1 Examples of basic setting B40 MF ____________________ 24
4.2 Examples of basic setting B45-2 MF _________________ 25
4.3 Setting values for nozzle assembly B40 MF ________ 26
4.4 Setting values for air damper B40 MF _______________ 26
4.5 Setting values for nozzle assembly B45-2 MF _____ 26
4.6 Setting values for air damper B45-2 MF ____________ 26
4.7 Nozzle assembly control, brake plate ________________ 27
4.8 Air setting B40 MF _________________________________________ 27
4.9 Air setting B45-2 MF Damper motor _________________ 28
5. BURNER SERVICING ________________________________________ 30
5.1 Servicing the combustion assembly _________________ 30
5.2 Servicing air dampers ____________________________________ 31
5.3 Replacement of damper motor B45-2 MF__________ 32
5.4 Replacement of oil pump B40 MF / B45-2 MF ____ 33
5.5 Replacement of preheaters _____________________________ 34
5.6 Replacement of electrical components ______________ 35
5.7 Replacement of preheater overheating protector _ 35
5.8 Check oil line seals _________________________________________ 36
5.9 Check pressure piston nozzle holder seals _________ 36
5.10 Replacement of pressure piston and seat __________ 37
5.11 Immersion heaters for extra preheating ______________ 38
5.12 Replacement of pump filter______________________________ 40
5.13 Check/service oil pre-filter _______________________________ 40
6. Preheater ____________________________________________________________ 41
6.1 Technical data preheater _________________________________ 41
6.2 Adjustment of preheater operating thermostat ____ 42
7. PUMP INSTRUCTION PUMP E4NC-1069 7P ___ 43
7.1 Technical data _______________________________________________ 43
7.2 Components _________________________________________________ 43
7.3 Oil connection _______________________________________________ 43
7.4 Changing the filter __________________________________________ 43
7.5 Function _______________________________________________________ 44
7.6 Preheating pump ___________________________________________ 44
7.7 Return Oil Pressure Switch ______________________________ 45
8. ELECTRICAL EQUIPMENT _______________________________ 46
8.1 B40 MF wiring diagram LMO24.255 ... _____________ 46
8.2 B45-2 MF wiring diagram LMO24.255... ___________ 47
8.3 Component list LMO24.255 ... ________________________ 48
8.4 Function LMO24.255 ... __________________________________ 48
8.5 Technical data LMO24.255... ___________________________ 49
8.6 Colour codes ________________________________________________ 50
8.7 Fault codes ___________________________________________________ 50
9. FAULT LOCATION ______________________________________________ 51
9.1 Burner will not start ________________________________________ 51
9.2 The burner does not start after normal operation 51
9.3 Delayed ignition _____________________________________________ 52
9.4 Noise in pump _______________________________________________ 52
9.5 Pump pressure ______________________________________________ 52
10. DECLARATION OF CONFIRMITY ______________________ 53