Binder CB 60-UL - Inner Chamber

Binder CB 60-UL

145 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

CB (E6.1) 07/2017 Page 18/145

2.3 Inner chamber

Figure 5: CB 160 with O

2

control and options

(A)

(B)

(C)

(D)

(

D2)

(G)

(F)

(E)

(

H)

(I)

(

J)

(

K)

(

L)

Table of Contents

Default Chapter2
- Table of Contents2
Safety6
- Legal Considerations6
- Structure of the Safety Instructions6
- Localization / Position of Safety Labels on the Chamber8
- Type Plate10
- General Safety Instructions on Installing and Operating the CO Incubator11
- Precautions When Working with Gases12
- Precautions When Handling Gas Cylinders14
- Intended Use15
Chamber Description16
- Chamber Overview17
- Instrument Panel17
- Inner Chamber18
- Control Panel on the Rear of the Chamber20
Completeness of Delivery, Transportation, Storage, and Installation21
- Unpacking, and Checking Equipment and Completeness of Delivery21
- Guidelines for Safe Lifting and Transportation21
- Storage22
- Location of Installation and Ambient Conditions22
Installation and Connections26
- Shelves26
- Permadry™ Water Pan26
- Connecting the O27
  - Control)27
- Gas Connections28
- Electrical Connection34
- Handling and Aligning the Divided Inner Door, Gas Proof (Optional Equipment)35
Start up36
- Equilibration Time36
- Factory Settings36
Functional Overview of the T4.12 Chamber Controller37
- Menu Structure38
- Operating Modes41
  - Activating the "Control Off" Mode or Change to "Fixed Value" Operating Mode41
- Deactivating the O43
- Humidity Control of the Permadry™ System45
- Turning on / off the Interior Socket Voltage (with Optional Interior Socket)46
- Performance During and after Power Failure46
- Information47
Setpoint Entry48
- Setting Ranges48
- Note When Setting High Gas Concentrations48
- Entering the Setpoints Via "Quick Menu50
- Entering the Setpoints Via General Menu52
Key Lock54
- Directly Activating the Key Lock55
- Automatic Key Lock55
- Changing the Password for Unlocking the Key Lock57
General Controller Settings58
- Setup Wizard59
- Date and Time Settings59
- Selecting the Menu Language of the T4.12 Controller61
- Setting Display Brightness61
- Changing the Temperature Unit62
- Defining the Data Recording Rate62
- Factory Reset63
- Network Configuration63
- Display of the Network Configuration67
- RS 422 Address (with Optional RS 422 Interface)68
- Display and Entry of the Device Configuration - for Service Purpose68
Data Transfer Via Usb Interface69
- Exporting Data to USB Drive69
- Importing Data from USB Drive70
Notifications and Alarms71
- Notifications Overview71
- Alarm Messages Overview71
- Alarm Status73
- Confirming an Active "Set" Alarm74
- Alarm Configuration and Overview75
- Zero-Voltage Relay Alarm Output82
Event List83
Graphical Display of the Measured Values84
- Setting the Sampling Rate84
- Defining the Display Range85
- Selecting the Parameters86
Temperature Safety Devices87
- Overtemperature Protective Device (Class 1)87
- Overtemperature Safety Controller (Temperature Safety Device Class 3.1)87
  - Safety Controller Modes87
  - Setting the Safety Controller88
Options91
- Communication Software APT-COM™ 3 Datacontrolsystem (Option)91
- RS 422 Interface (Option)91
- Silicone Access Ports 30 MM / 1.18 In, Closable from both Sides with Silicon Plugs (Option)91
- Interior Socket 230V (Option)92
- Analog Outputs for Temperature and CO (Option)94
- Access Port for Extra-Low Voltage (Option)94
- BINDER Gas Supply Service - External Bottle Changer for CO95
- N 2 or O 2 (Option)95
- Stands96
Reference Measurements97
- CO Reference Measuring97
  - Measuring CO 2 Concentration Indirectly Via the Ph of the Cell Medium97
- Directly Via Chemical Indicator Tubes98
- Temperature Reference Measurement99
- Directly with an Electronic Infrared Measuring Device99
Avoiding Microbial Contamination99
- Cells and Media99
- Laboratory Conditions / Equipment Around the Incubator99
- Working and Behavior in the Lab100
- Chamber Design and Equipment of the CO Incubator100
- Handling the CO Incubator101
Cleaning, Decontamination / Disinfection, and Sterilization103
- Cleaning103
- Decontamination / Chemical Disinfection of the Chamber105
- Hot-Air Sterilization at 180 °C / 356 °F106
Maintenance and Service115
- Maintenance Intervals, Service115
- Checking the Air Jacket Heating Fan116
- Checking the Humidity System Fan116
- Gas Inlet Fine Filter116
- Sending the Chamber Back to BINDER Gmbh116
Disposal117
- Disposal of the Transport Packing117
  - Outer Chamber Packing117
  - Packing Inside the Chamber and Equipment117
- Decommissioning118
- Disposal of the Chamber in the Federal Republic of Germany118
- Disposal of the Chamber in the Member States of the EU Except for the Federal Republic of Germany119
- Disposal of the Chamber in Non-Member States of the EU120
Troubleshooting121
- General121
- Heating121
- Gas Cylinder Pressure too Low123
- Gas Concentration124
- Sterilization126
- Humidity126
- Controller127
- Open Door127
Technical Description128
- Factory Calibration and Adjustment128
- Over Current Protection128
- Definition of Usable Volume128
- CB Technical Data129
- Equipment and Options131
- Accessories and Spare Parts (Extract)132
- Important Conversion Data for Non-SI Units133
- Conversion Table for Gas Inlet Pressures, Bar - Psi133
- Dimensions CB 60134
- Dimensions CB 160135
- Dimensions CB 220136
Certificates and Declarations of Conformity137
- EU Declaration of Conformity137
Product Registration139
Contamination Clearance Certificate140
- For Chambers Located Outside the USA and Canada140
- For Chambers in the USA and Canada143

Related product manuals

Preview: Binder CB Series

Binder CB Series

Preview: Binder C 170

Binder C 170 E3

Binder CB260-230V-O

Preview: Binder BD 56

Binder KMF-240-UL