Binder MK 115 - Certificate for the GS Mark of Conformity of the Deutsche Gesetzliche Unfallversicherung E.V. (German Social Accident Insurance) DGUV

159 pages

Save Page as PDF

To Next Page

To Previous Page

MK / MKT (E5) 03/2019 page 149/158

25.3 Certificate for the GS mark of conformity of the “Deutsche Gesetzliche Un-

fallversicherung e.V.“ (German Social Accident Insurance) DGUV

Main Page

Default Chapter2
- Table of Contents2
1 Safety6
- Legal Considerations6
- Structure of the Safety Instructions6
- Localization / Position of Safety Labels on the Chamber8
- Type Plate9
- General Safety Instructions on Installing and Operating the Chamber10
- Intended Use12
- Operating Instructions13
- Measures to Prevent Accidents13
2 Chamber Description14
- Chamber Overview15
- Instrument Panel15
- Lateral Control Panel16
- Main Power Switch (MK 56)17
- Rear Power Switch (MK / MKT 115, 240, 720)17
- Rear Chamber View18
3 Completeness of Delivery, Transportation, Storage, and Installation20
- Unpacking, and Checking Equipment and Completeness of Delivery20
- Guidelines for Safe Lifting and Transportation21
- Storage21
- Location of Installation and Ambient Conditions21
4 Installation and Connections23
- Connection of Cooling Water Outlet for Water Cooling (Option for MK 56)23
- Connection of Cooling Water Inlet for Water Cooling (Option for MK 56)23
- Installation of the Voltage and Frequency Changer (Chambers with Voltage and Frequency Changer)24
- Electrical Connection26
  - Information on Connecting the Alternating Climate Chamber26
  - Connecting the Voltage and Frequency Changer (for Chambers Equipped with a Voltage and Frequency Changer)27
5 Functional Overview of the Mb2 Chamber Controller28
- Operating Functions in Normal Display29
- Display Views: Normal Display, Program Display, Chart-Recorder Display30
- Controller Icons Overview31
- Operating Modes33
- Controller Menu Structure34
- Principle of Controller Entries37
- Performance During and after Power Failures37
- Performance When Opening the Door38
6 Start up38
- Turning on the Chamber38
- Controller Settings Upon Start up39
7 Set-Point Entry in "Fixed Value" Operating Mode40
- Set-Point Entry through the "Setpoints" Menu40
- Direct Setpoint Entry Via Normal Display41
- Special Controller Functions Via Operation Lines41
8 Timer Program: Stopwatch Function43
- Starting a Timer Program43
  - Performance During Program Delay Time43
- Stopping a Running Timer Program44
  - Pausing a Running Timer Program44
  - Cancelling a Running Timer Program44
- Performance after the End of the Program44
9 Time Programs45
- Starting an Existing Time Program45
  - Performance During Program Delay Time46
- Stopping a Running Time Program46
  - Pausing a Running Time Program46
  - Cancelling a Running Time Program46
- Performance after the End of the Program46
- Creating a New Time Program47
- Program Editor: Program Management47
  - Deleting a Time Program48
- Section Editor: Section Management49
- Value Entry for a Program Section52
10 Week Programs58
- Starting an Existing Week Program58
- Cancelling a Running Week Program58
- Creating a New Week Program59
- Program Editor: Program Management60
  - Deleting a Week Program61
- Section Editor: Section Management62
- Value Entry for a Program Section64
11 Notification and Alarm Functions67
- Notification and Alarm Messages Overview67
  - Notifications67
  - Alarm Messages68
- State of Alarm68
- Resetting an Alarm, List of Active Alarms69
- Activating / Deactivating the Audible Alarm (Alarm Buzzer)69
12 Temperature Safety Devices70
- Over Temperature Protective Device (Class 1)70
- Overtemperature Safety Controller Class 270
- Over/Under Temperature Safety Device Class 2 (Option)73
13 User Management74
- Authorization Levels and Password Protection74
- Log in77
- Log out78
- User Change78
- Password Assignment and Password Change79
- Activation Code83
14 General Controller Settings84
- Selecting the Controller's Menu Language84
- Setting Date and Time84
- Selecting the Temperature Unit86
- Display Configuration86
  - Adapting the Display Parameters86
  - Touchscreen Calibration87
- Network and Communication88
- USB Menu: Data Transfer Via USB Interface92
- Turning off the Interior Lighting Automatically93
15 General Information93
- Service Contact Page93
- Current Operating Parameters94
- Event List95
- Technical Chamber Information95
- Self-Test Function (MK 56)96
16 Chart Recorder Display98
- Views98
- Setting the Parameters102
17 Notes on Refrigerating Operation103
18 Anti-Condensation Protection Via Operation Line104
19 Zero-Voltage Switching Outputs Via Operation Lines105
20 Options106
- APT-COM™ 4 Multi Management Software (Option)106
- RS485 Interface (Option)106
- Data Logger Kit (Option)106
- Analog Outputs for Temperature (Option)106
- Compressed Air Connection (Option)107
- Compressed Air Dryer (Option)107
- Water Cooling (Option)109
- Object Temperature Display with Flexible Pt 100 Temperature Sensor (Option)109
21 Maintenance, Cleaning, and Service110
- Maintenance Intervals, Service110
- Cleaning and Decontamination111
  - Cleaning111
  - Decontamination113
- Sending the Chamber Back to BINDER Gmbh114
22 Disposal114
- Disposal of the Transport Packing114
- Decommissioning115
- Disposal of the Chamber in the Federal Republic of Germany115
- Disposal of the Chamber in the Member States of the EU Except for the Federal Republic of Germany116
- Disposal of the Chamber in Non-Member States of the EU117
23 Troubleshooting118
24 Technical Description121
- Factory Calibration and Adjustment121
- Over-Current Protection121
- Definition of Usable Volume121
- MK (E4) Technical Data122
- MKT (E4) Technical Data124
- Equipment and Options (Extract)126
- Accessories and Spare Parts (Extract)127
- MK Heating-Up and Cooling-Down Graphs128
- MKT Heating-Up and Cooling-Down Graphs132
- MK Heat Compensation135
- MKT Heat Compensation136
- Dimensions138
25 Certificates and Declarations of Conformity143
- EU Declaration of Conformity for MK143
- EU Declaration of Conformity for MKT146
  - Certificate for the GS Mark of Conformity of the "Deutsche Gesetzliche Unfallversicherung E.V." (German Social Accident Insurance) DGUV149
26 Product Registration151
- Registering a BINDER Chamber151
- Multi Management Software APT-COM™ 4 BASIC-Edition152
27 Contamination Clearance Certificate153
- For Chambers Located Outside the USA and Canada153
- For Chambers Located in the USA and Canada156

Binder MK 115 - Certificate for the GS Mark of Conformity of the Deutsche Gesetzliche Unfallversicherung E.V. (German Social Accident Insurance) DGUV

Table of Contents

Related product manuals