BONFIGLIOLI HDP Series User Manual

120
input
VP
GL
GR
input
AD
input
VP
GL
GR
input
AD
HDP 80
Rn
2
[kN]
n
2
xh
M
2
= 11450 Nm M
2
= 9150 Nm M
2
= 7600 Nm M
2
= 5700 Nm
250 000
39.3 46.0 43.7 46.0 45.3 46.0 47.2 46.0
37.1 46.0 40.3 46.0 42.4 46.0 45.1 46.0
500 000
26.0 41.7 32.3 46.0 35.3 46.0 37.2 46.0
27.1 39.9 30.3 43.1 32.5 45.2 35.1 46.0
750 000
16.7 33.5 25.8 39.3 29.8 41.6 32.3 43.5
20.0 33.5 25.4 36.7 27.5 38.8 30.2 41.4
1 000 000
10.4 28.1 21.5 34.2 25.8 37.6 29.1 39.5
14.8 29.4 22.2 32.6 24.4 34.7 27.0 37.3
1 250 000
— 24.2 17.8 30.5 22.8 34.3 26.9 36.5
— 25.7 19.5 29.7 22.1 31.8 24.8 34.4
2 500 000
— 10.1 — 20.0 13.5 24.3 19.7 28.6
— 13.0 — 21.3 15.2 23.9 18.6 26.5
3 750 000
— — — 13.8 — 19.1 15.7 24.1
— — — 15.3 — 19.9 15.6 22.5
5 000 000
— — — — — 15.8 13.1 21.0
— — — 11.2 — 16.8 13.6 20.0
HDP 80
Rn
2
[kN]
n
2
xh
M
2
= 11450 Nm M
2
= 9150 Nm M
2
= 7600 Nm M
2
= 5700 Nm
250 000
27.5 43.6 32.6 46.0 36.1 46.0 40.3 46.0
23.3 39.4 29.2 45.2 33.3 46.0 38.2 46.0
500 000
17.5 30.7 22.7 35.7 26.1 39.1 30.3 43.2
13.3 26.5 19.3 32.4 23.3 36.3 28.2 41.1
750 000
12.6 24.3 17.7 29.3 21.2 32.7 25.4 36.8
— 20.1 14.4 26.0 18.3 29.9 23.3 34.7
1 000 000
— 20.2 14.5 25.3 18.0 28.6 22.2 32.8
— 16.1 11.2 21.9 15.2 25.8 20.2 30.7
1 250 000
— 17.3 12.3 22.3 15.7 25.7 20.0 29.8
— 13.1 — 19.0 13.0 22.9 17.9 27.7
2 500 000
— 9.4 — 14.4 — 17.8 13.8 21.9
— — — 11.0 — 15.0 11.8 19.8
3 750 000
— — — 10.4 — 13.8 — 18.0
— — — — — 11.0 — 15.9
5 000 000
— — — — — 11.3 — 15.4
———————13.4
Carichi radiali ammissibili relativi ai cusci
-
netti secondo variante HDB.
Albero al quale sono riferiti i carichi radiali
ammissibili. Per gli alberi bisporgenti il cari
-
co può essere applicato solo sull’estremità
così evidenziata. In caso diverso consultare
il Servizio Tecnico Bonfiglioli.
Rated overhung loads relevant to rein
-
forced bearings type HDB.
Zulässige Radialkräfte der Lager gemäß
Variante HDB.
Welle, auf die sich die zulässigen Radialkräfte
beziehen. Für die Wellen mit zwei Wellenzap
-
fen kann die Kraft nur auf das so gekenn
-
zeichnete Wellenende ausgeübt werden. An
-
dernfalls mit dem technischen Kundendienst
von Bonfiglioli Rücksprache halten.
h: durata in ore riferita al cuscinetto dell'albero
lento.
h: expected lifetime [hours] for bearing of the
output shaft.
h: Lebensdauer in Stunden für das Lager der
Abtriebswelle.
Shaft the rated overhung load is applicable to.
For double extended shaft the load is only ap
-
plicable to the extension highlighted Should
this not be the case consult Bonfiglioli’s Tech
-
nical Service.
(—) Consultare il Servizio Tecnico Bonfiglioli (—) Contact the Bonfiglioli Technical Service. (—) Bitte wenden Sie sich an den technischen
Kundendienst von Bonfiglioli.
SH
SH
LP
LP

BONFIGLIOLI HDP Series Specifications

General

Brand	BONFIGLIOLI
Model	HDP Series
Category	Industrial Equipment
Language	English