What to do in case of malfunctions? NL
3What to do in case of malfunctions?
Fix faults yourself
You can often easily remedy technical faults on the
device yourself.
What to do at jst or ingen?Malfunctions are often caused by a trifle. Before
contacting the
If a dish does not turn out optimally, you will find
many tips and instructions for preparation at the end
of the instructions for use. ~"
Tested for you in our
cooking studio." on page 30
after-sales service to solve the fault yourself using the
of the table.
Malfunction Possible cause Solution / clue
Device not working Fuse defective
Power failure
Power failure
Check the fuse in the meter box.
Check whether the kitchen light or other kitchen appliances are
working. Reset the language and time.The display shows “Sprache
Deutsch”.
When the device is switched off, Basic setting changed. Change the basic setting of the time display
the current time does not appear.
The appliance door cannot be
opened.
The appliance door is locked
with the child lock.
Deactivate the child lock by pressing the field for approx. 4 secondsdto push.
The lock can be deactivated in the basic settings. Wait until the cooking
compartment has cooled down and the . symboln has disappeared.The appliance door cannot be
opened, the symbol is shown
in the display n lit
Appliance door is locked by
the cleaning function.
The appliance does not heat up, on the dis-
The demonstration mode is
activated in the basic
settings.
Disconnect the device from the mains for a while (switch off the fuse in the
fuse box) and then deactivate the demonstration mode within 3 minutes in the
basic settings.
play is the symbol mno longer
lit.
The appliance does not start and
the display shows “Interior too hot”
The cooking compartment is
too hot for the selected food
or the type of heating
Let the interior cool down and start again
The control ring has fallen out of the
bearing on the control panel.
The control ring has been
accidentally unlocked.
The control ring is removable. Simply put the control ring back into
the bearing on the control panel and push it in so that it locks and
can be turned normally again.
The control ring can no
longer be turned easily.
There is dirt under the
control ring.
The control ring is removable. To unlock it, simply pull it out of
the bearing. Or you can press the outer edge of the ring so that it
tilts and can be picked up easily.
Carefully clean the control ring and bearing on the device with
soapy water and a cleaning cloth. Dry with a soft cloth. Do not
use sharp or abrasive agents for this. Do not soak or put in the
dishwasher.
Do not remove the control ring too often, so that the bearing remains stable.
- - - - - - - -
:Warning – Risk of injury!
If it concerns a one-off fault, the indication disappears.
If the error message reappears, please contact
customer service and indicate exactly what the error
message is.
Improper repairs are dangerous. Never attempt to
repair the device yourself. Repairs should only be
performed by technicians instructed by customer
service. Contact the service department in the event of a
defect in the appliance;
Maximum operating time
:Warning – Risk of electric shock!
If you have not changed the settings of your appliance
for several hours, the heating will stop automatically.
This prevents the device from continuing to work
unintentionally.
Improper repairs are dangerous. Repairs and the
replacement of damaged connection cables may only be
carried out by technicians instructed by customer
service. If the device is defective, remove the plug from
the socket or switch off the fuse in the meter box.
Contact customer service.
The time when the maximum operating time is
reached depends on the function settings.
Maximum operating time reached
A message appears on the display indicating that the maximum
operating time has been reached.
Error messages on the display
If an error message with “D” or “E” appears on the
display, e.g. D0111 or E0111, switch the device on with
the on/off button ÿ out and in again.
To continue operation, tap any field or turn the control
ring.
When you are not using the device, switch it off with
the on/off button ÿ from.
27
To Next Page
Loading...
