Bosch ICP-CC408 - Page 5

ICP-CC408 | Installation Guide | Contents EN | 5
Bosch Security Systems, Inc. | 12/08 | F01U089463-02
15.22
Test Reporting Dialer Options ......................68
16.0 Programmable Outputs...................................68
16.1 Redirecting Outputs to the Codepad Buzzer69
16.2 Output Event Types........................................69
16.3 Output Polarity ................................................74
16.4 Output Timing .................................................75
16.5 Pulsing Polarities..............................................75
16.6 One-Shot Polarities..........................................75
17.0 System Event Timers ......................................76
17.1 Programming Entry/Exit Timers...................76
17.2 Entry Timer 1...................................................76
17.3 Entry Timer 2...................................................76
17.4 Exit Time ..........................................................76
17.5 Entry Guard Timer for STAY Mode............76
17.6 Delay Alarm Reporting Time........................76
17.7 Sensor Watch Time.........................................76
17.8 Codepad Lockout Time..................................77
17.9 Siren Run Time................................................77
17.10 Siren Sound Rate.............................................77
17.11 Auto Arming Pre-Alert Timer .......................77
17.12 Auto Arming Time..........................................77
17.13 Auto Disarming Time .....................................77
17.14 Kiss-Off Wait Time .........................................77
17.15 System Time.....................................................78
17.16 System Date......................................................78
18.0 System and Consumer Options.....................78
18.1 System Options 1.............................................78
18.2 System Options 2.............................................79
18.3 System Options 3.............................................79
18.4 System Options 4.............................................80
18.5 Consumer Options 1.......................................80
18.6 Consumer Options 2.......................................81
18.7 Consumer Options 3.......................................81
18.8 Radio Input Options .......................................81
19.0 Partitioning .......................................................82
19.1 ICP-CP500PW Master Partitioned LED
Codepad............................................................82
19.2 Using Codepads in a Partitioned System .....82
19.2.1 Operating with a CP5 Area Addressable
LED Codepad ..................................................82
19.2.2 Operating with a CP5 Master Partitioned
Codepad............................................................82
19.3 Programming....................................................82
19.3.1 Partitioning Options 1.....................................83
19.3.2 Partitioning Options 2.....................................83
19.4 Zone Allocations..............................................83
19.4.1 Zone Allocations for Area 1...........................84
19.4.2 Zone Allocations for Area 2...........................84
19.5 User Code Allocations....................................84
19.6 Setting Up and Programming Codepads for
Partitioning....................................................... 85
19.6.1 Setting Up the Master Partitioned Codepad
as the Main Codepad ..................................... 85
19.6.2 Setting Up an Area 1 Codepad as the Main
Codepad........................................................... 85
19.6.3 Setting Up an Area 1 Codepad..................... 85
19.6.4 Setting Up an Area 2 Codepad..................... 85
19.7 Codepad Connections For Partitioning -
Examples.......................................................... 85
20.0 Optional Equipment....................................... 86
20.1 RE012/E and RE013/E 2-Channel/
4-Channel Hand-Held Transmitters 304
MHz.................................................................. 86
20.2 WE800/E 304 MHz RF Receiver................. 86
20.3 RE005/E: 2-Channel Radio Interface.......... 87
20.4 SS914 EDMSAT Satellite Siren.................... 87
20.5 CC891 Programming Key............................. 87
20.6 CC816 Alarm Link Software......................... 87
20.7 ICP-CP508W Eight Zone LED Codepad.... 87
20.8 ICP-CP508LW Eight Zone LCD Codepad) 87
20.9 ICP-CP500AW Eight Zone Area
Addressable Codepad .................................... 87
20.10 CP500PW Master Partitioned Codepad...... 87
20.11 CP105A Night Arm Station........................... 88
20.12 TF008 Plug Pack (TF008) .............................. 88
21.0 Terminals and Descriptions........................... 89
21.1 Terminal Descriptions.................................... 89
21.2 Glossary Of Terms.......................................... 90
21.3 Diagrams .......................................................... 92
22.0 Appendices ...................................................... 96
22.1 Appendix A – Telephone Anti-Jamming .... 96
22.2 Appendix B – Test Reports Only When
Armed............................................................... 96
23.0 Specifications ................................................... 97
23.1 Warranty Statement........................................ 97
23.2 Software Version Number............................. 97
23.3 Advice to Users ............................................... 97
23.4 New Zealand Telepermit Notes.................... 98
24.0 Programming Sheets....................................... 98
25.0 Country Codes .................................................... 105
Figures
Figure 1: ICP-CP508W Eight Zone LED Codepad16
Figure 2: ICP-CP508LW Eight Zone LCD
Codepad.................................................... 17
Figure 3: ICP-CP500PW Master Partitioned
Codepad.................................................... 18
Figure 4: ICP-CP508W LED Codepad Showing
Audible Alarm Buttons........................... 22