Bosch Solution 16plus - Menu Reference; Navigation and Access Levels

15
Bosch Security Systems 03/10 BLCC100U
Solution16
Plus
User Guide
2. Use the [] and [] keys to select the area that you want
to turn chime mode on or o, then press [OK] to select.
Alternatively, you can enter the area number that you
want to turn chime mode on or o, then press [OK].
The keypad will display the following when chime mode
is turned o:
Reception Area A001
Chime Is OFF,
To Turn ON, Press ON.
To Go Back Press OK
The keypad will display the following when chime mode
is turned on:
Reception Area A001
Chime Is ON,
To Turn OFF, Press OFF.
To Go Back Press OK
3. Press the [ON] key to turn chime mode on, or, press [OFF]
to turn chime mode o.
4. Press the [OK] key to exit.
Areas > Area Properties >
Area Name
MENU 2-1-0
This menu allows you to program the name for each area. Each
area name can be programmed with up to 16 characters. At
factory default, only Area 1 is used. The Solution 16
Plus
control
panel can have a maximum of 4 independent areas programmed.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [1] + [0].
A list of dierent areas will display on the keypad.
2. Use the [] and [] keys to select the area that you
want to program the name, then press [OK] to select.
Alternatively, you can enter the area number that you
want to program the name, then press [OK].
The keypad will display the following:
Area Name A001
Area 1 Name
Press
 OK to SAVE
3. Use the [] and [] keys to scroll the cursor left and right
across the area name text. Use the [] and [] keys to
scroll through the dierent characters available. To clear
all text from the cursor position to the right, press the
[OFF] key.
4. When the user name is complete, press [OK].
Inputs
Each Solution 16
Plus
control panel has up to a maximum 16 zones.
When the optional radio receiver is tted any available zone may
be programmed as a wireless zone. Your installer will advise you
on the exact makeup and conguration of your system.
Inputs > Commands >
Zone Status
MENU 3-0-0
This menu allows you to view the zone status of each zone (i.e.
Normal, Open or Short).
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [3] + [0] + [0].
A list of dierent zones will display on the keypad.
2. Use the [] and [] keys to select the zone that you want
to turn view the status information then press [OK] to
select. Alternatively, you can enter the zone number that
you want to view status information, then press [OK].
The keypad will display the following zone status
information:
Zone 1 Name Z001
EOL=Normal 06523 ohms
Press OK or MENU
3. Press the [OK] key to exit.
Inputs > Commands >
Bypass Zones
MENU 3-0-2
This menu allows you to bypass or un-bypass a single or multiple
zones before you turn the area All On, Part On or Part 2 On.
When bypassing zones, it disables the ability for a zone to detect
intrusion and sound an alarm.
A burglary zone will automatically become un-bypassed when
you turn the corresponding area o (disarm). Any 24-Hr re or
24-Hr non re zones will need to be manually un-bypassed.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [3] + [0] + [2].
A list of zones that can be bypassed will display on the
keypad. A ‘√’ displayed on the right side of the zone
name indicates that the zone is already bypassed.
Z001 Zone 1 Name 
Z002 Zone 2 Name
Z003 Zone 3 Name
Press
 OK or MENU
2. Use the [] and [] keys to select the zone that you want
to bypass, then press [OK]. Alternatively, you can enter
the zone number that you want to bypass, then press
[OK].
If the zone is bypassed, the keypad will prompt:
Zone 1 Name Z001 is
bypassed. To un-bypass,
press OFF.
Press OK or MENU