How to fix Boss Voice Recorder power won't turn on?
To troubleshoot a Boss Voice Recorder that won't turn on, ensure the power switch is set to “USB” if using USB bus power, or to “ON” if using the AC adapter or batteries. Also, if you're using a notebook computer running on battery, connect an AC adapter to your computer. Check your computer's settings and if using a USB hub, ensure it is self-powered.
Why no sound from my Boss BR-800?
If you're not getting any sound from your Boss Voice Recorder, first check that the BR-800 and any connected equipment are powered on. Ensure the PHONES LEVEL isn't set to 0, the audio cables are correctly connected and not broken, and the volume on any connected amp or mixer isn't turned down. Also, check that the [MASTER] fader isn't lowered, a supported SD card is inserted, you're not trying to play back a phrase shorter than 1.0 seconds, and DIR MONITOR isn't turned 'OFF'.
How to eliminate noise in Boss Voice Recorder?
If your Boss Voice Recorder recorded sound contains noise or distortion, adjust the input sensitivity so that the PEAK indicator briefly lights when the loudest passages occur. If the noise or distortion occurs after mastering, the track output levels may be too high. If needed, pass the signal through a commercially available microphone preamp before recording.
What to do if can't record with Boss BR-800?
If you can't record with your Boss Voice Recorder, check if the song is protected. Ensure an SD card is inserted and has sufficient free space, and that it is not locked. Also, verify that you are not using the Phrase Trainer, scrub playback, or control surface mode.
How to stop oscillation in Boss Voice Recorder?
If you're experiencing oscillation with your Boss Voice Recorder, you can stop playback in your software, turn off the Soft Thru function, turn off the audio input of your software, or change INPUT SELECT to a setting other than “USB.”
How to turn off reverb in Boss Voice Recorder?
To turn off the reverb on your Boss Voice Recorder, check the reverb send level amounts for the loop effect. Set each track’s send level amount to '0' to disable the reverb effect.
Why can't hear input source on Boss Voice Recorder?
If you can't hear the input source on your Boss Voice Recorder, ensure that INPUT SELECT is set correctly. Also, check if you have adjusted the INPUT SENS knob appropriately and that the [REC LEVEL] knob is not minimized.
Why is the volume low on my Boss BR-800?
If you're getting insufficient volume from a device connected to the GUITAR/BASS jack or LINE IN jack on your Boss Voice Recorder, use a connection cable that does not contain a resistor. Also, make sure the volume of your external device is adjusted correctly.
Why no sound from a track on Boss Voice Recorder?
If there is no sound from a specific track on your Boss Voice Recorder, check if the track’s volume level is lowered, the wrong V-track is selected, or the track is muted.
Why Boss BR-800 Voice Recorder can’t play WAV file?
If your Boss Voice Recorder can’t play back a WAV file, it could be due to attempting to play back a WAV file in an unsupported format.
General| Simultaneous Playback Tracks | 8 |
|---|---|
| Sampling Frequency | 44.1 kHz |
| A/D Conversion | 24-bit |
| D/A Conversion | 24-bit |
| USB Interface | USB 2.0 |
| Data Format | WAV, MP3 |
| Internal Microphones | Stereo |
| Display | Backlit LCD |
| Power Supply | AC adapter or AA batteries |
| Storage Media | SD/SDHC card |
| Effects | Yes (BOSS COSM effects) |
Outlines the essential steps to prepare for recording sessions on the BR-800.
Details the fundamental procedures for recording and playing back audio.
Explains how to record tracks while using insert or master effects.
Guides on recording musical parts along with built-in rhythm patterns.
Covers various methods for editing recorded tracks and songs.
Details the process of applying mastering effects for final song polish.
Explains the meaning of warning and caution symbols used in the manual.
Clarifies the interpretation of various safety symbols and their implications.
Provides essential information on power sources and battery handling.
Offers advice on selecting the best location for the BR-800.
Details recommended methods for cleaning and maintaining the unit.
Advises on managing data when the unit requires servicing.
Lists further important recommendations for safe and effective operation.
Provides guidelines for inserting and using SD cards.
Offers instructions for proper handling of DVD-ROM discs.
Explains legal considerations for recording and distributing copyrighted works.
Advises on proper operation of the BR-800's touch-sensitive buttons.
Highlights the simultaneous recording and playback capabilities.
Describes the extensive range of high-quality effects available.
Details the rhythm generator and its features for song creation.
Explains the simplified process for quick recording setup.
Introduces the function for recording musical ideas and phrases.
Covers the various ways the BR-800 can connect via USB.
Mentions the convenience of built-in stereo microphones for recording.
Lists the available power sources: AC adapter, batteries, and USB.
Details the knobs, faders, and indicators on the top panel.
Explains the function of various operational buttons and track faders.
Describes the navigation, menu, and mode selection buttons.
Explains the information displayed, including song status and level meters.
Details the headphone and guitar/bass input jacks on the front panel.
Describes the rear panel's output, pedal, and input jacks.
Explains the SD card slot, USB connector, and power switch.
Guides on connecting equipment to play demo songs.
Instructions for powering the unit on and off correctly.
Steps to select and play demo songs from the SD card.
Details fader adjustments for optimal demo song playback volume.
Guides on setting up source, category, and effect parameters for EZ Recording.
Explains the steps to initiate and conduct recording using EZ Recording.
Details how to play back tracks recorded using the EZ Recording function.
Lists and explains the parameters available for EZ Recording.
Illustrates general equipment connections required for recording.
Explains how to use the cord hook for cable management.
Guides on creating new songs and selecting existing ones for recording.
Details selecting input sources and adjusting input sensitivity.
Explains how to adjust recording levels and select tracks for recording.
Guides on choosing between virtual tracks for recording.
Covers adjusting stereo panning and basic recording steps.
Explains the loop recording function for phrase repetition.
Details the steps for playing back recorded tracks.
Guides on recording new parts onto existing tracks.
Explains how to set specific regions for repeated playback.
Details using Quantize for precise repeat region setting.
Explains how to manually punch in and out during recording.
Guides on using an external foot switch for punch-in/out operations.
Details setting up predefined punch-in/out points automatically.
Explains the recording process when using auto punch-in/out.
Explains how to revert to the state before the last operation.
Details how to cancel a previously performed Undo operation.
Shows how to display the remaining recording time on the screen.
Explains how to view song name, size, and other information.
Guides on entering and navigating Song Sketch mode.
Explains how to record audio files in Song Sketch mode.
Details playing back and erasing WAV files within Song Sketch.
Covers naming WAV files and viewing their information.
Introduces insert effects, patch organization, and bank types.
Explains how to enable or disable insert effects.
Guides on easily creating custom sounds using the EZ TONE function.
Details how to edit parameters for insert effects.
Explains how to save edited effect settings as new patches.
Details how to change where insert effects are applied in the signal chain.
Explains how to copy effect patches between banks.
Lists available effect algorithms and their components.
Details parameters for Compressor/Limiter effects.
Details parameters for Distortion effects.
Details parameters for Booster effects.
Details parameters for COSM Amp simulations.
Details parameters for microphone simulation types.
Details parameters for the Equalizer effect.
Details parameters for the Noise Suppressor effect.
Details parameters for various modulation effects.
Details parameters for the Guitar Simulator effect.
Details parameters for the Bass Simulator effect.
Details parameters for the Slow Gear effect.
Details parameters for the Sitar Simulator effect.
Details parameters for the Pitch Shifter effect.
Details parameters for the Phaser effect.
Details parameters for the Flanger effect.
Details parameters for the Tremolo effect.
Details parameters for the Rotary effect.
Details parameters for the Uni-Vibe effect.
Explains the Pan effect for stereo imaging.
Details parameters for the Vibrato effect.
Details parameters for the Ring Modulator effect.
Details parameters for the Chorus effect.
Details parameters for the Doubling Delay effect.
Details parameters for the Delay effect.
Details parameters for the Acoustic Simulator effect.
Details parameters for the Guitar to Bass effect.
Details parameters for the Acoustic Processor effect.
Details parameters for the Pitch Correct effect.
Details parameters for the Dynamics effect.
Details parameters for Tone/SFX effects.
Details parameters for Double/Harmony effects.
Details parameters for the Low Cut filter effect.
Details parameters for the Lo-Fi effect.
Guides on adjusting loop effect depth via send levels.
Details how to edit loop effect parameters.
Details parameters for the Reverb effect.
Details parameters for Chorus and Delay effects.
Guides on adjusting the equalization for individual tracks.
Introduces the rhythm generator, patterns, and arrangements.
Explains what patterns are and their types (preset, song).
Details how to create and use song arrangements.
Explains the different drum kits available for patterns and arrangements.
Guides on enabling and disabling the rhythm function.
Explains the differences between Pattern and Arrangement modes.
Details how to select and play rhythm patterns.
Explains how to adjust pattern tempo and use the TAP TEMPO button.
Details how to select and play rhythm arrangements.
Explains how to adjust arrangement tempo and use the TAP TEMPO button.
Guides on selecting and changing drum kits.
Details the process of creating custom rhythm arrangements.
Explains how to add or remove steps within an arrangement.
Guides on assigning names to custom arrangements.
Explains the procedure for copying existing arrangements.
Details how to erase song arrangements.
Explains how to offset rhythm playback timing relative to audio tracks.
Explains Scrub and Preview for precise sound editing.
Guides on copying track data between different tracks.
Explains how to move track data within or between tracks.
Guides on erasing specific sections of track data.
Details exchanging data between two tracks.
Explains how to import WAV files into tracks.
Guides on copying songs, including to/from SD card.
Details the process for erasing songs from the SD card.
Explains how to assign custom names to songs.
Guides on enabling song protection to prevent overwrites.
Details saving the current state of a song.
Explains how saving frees up SD card space by erasing temporary data.
Explains the purpose and benefits of mastering effects for final mix.
Details the step-by-step process for applying mastering effects.
Guides on adjusting parameters for mastering effects.
Explains how to save edited mastering effect settings.
Lists and explains the parameters for mastering effects.
Guides on converting songs for computer playback and CD creation.
Details recording mastered songs to external devices like CD recorders.
Covers initial setup, SD card structure, DVD-ROM, and USB driver installation.
Details using the BR-800 for recording and playback with a computer.
Explains using the BR-800 to control DAW software via USB.
Explains integrating SONAR LE with the BR-800 for control.
Lists BR-800 controls and their functions in DAW control surface mode.
Guides on transferring files using the Wave Converter utility.
Explains how to back up and recover BR-800 data to/from a computer.
Details how to configure USB-related settings.
Lists and explains the parameters for USB functionality settings.
Details how USB audio output is routed (Master or Rec Level).
Guides on adjusting the LCD display contrast for readability.
Explains connecting and using foot switches and expression pedals.
Explains how the expression pedal functions with effects.
Guides on assigning functions (Play/Rec) to the foot switch.
Details how to use the built-in chromatic tuner for guitar/bass.
Guides on activating the instrument tuner.
Details the steps for tuning an instrument using the BR-800 tuner.
Explains how to adjust the tuner's reference pitch.
Explains how to mix external audio device input with BR-800 output.
Covers configuring audio output for LINE OUT and PHONES jacks.
Details splitting output between LINE OUT and PHONES.
Guides on adjusting headphone volume levels.
Introduces Phrase Trainer functions for practice.
Explains the Time Stretch function for slowing playback.
Details the Center Cancel function for isolating instruments.
Explains how to reset the BR-800 to its original factory state.
Guides on formatting SD cards for use with the BR-800.
Shows how to view the total and remaining capacity of the SD card.
Explains how to enable Power Save mode to conserve battery.
Details how to enable +48V phantom power for condenser microphones.
Guides on adjusting the sensitivity of the BR-800's touch sensors.
Lists compatible SD card types and capacities.
Provides estimated recording times based on SD card capacity.
Guides on formatting SD cards for the BR-800.
Details how to remove the SD card cover.
Instructions for properly inserting and removing SD cards.
Explains how to use the write protect lock on SD cards.
Lists all available insert effect patches categorized by bank.
Provides recommended connections for 4-Input Multi effects.
Lists the available mastering effects patches.
Details the structure and settings of preset arrangements.
Addresses common problems related to power supply and connection.
Solves problems related to no sound or incorrect sound output.
Addresses problems with SD card recognition, data, and formatting.
Solves problems related to USB connectivity and computer recognition.
Addresses unresponsive or overly sensitive touch buttons.
Lists common error messages and their corresponding causes and actions.
Provides technical specifications for the digital recorder.
To Next Page
