Why don't the headers or footers show up when printing from my Brother 8085DN - DCP B/W Laser All in One Printer?
If headers or footers don't show up when printing from your Brother All in One Printer, it's because there is an unprintable area on the top and bottom of the page. Adjust the top and bottom margins in your document to allow for this.
How to troubleshoot no printout issue on my Brother 8085DN - DCP B/W Laser?
If your Brother All in One Printer isn't printing, check the following: * Make sure the printer is plugged in and turned on. * Verify that the toner cartridge and drum unit are correctly installed. * Check the interface cable connection on both the printer and your computer. * Confirm the correct printer driver is installed and selected. * See if the LCD shows any error messages. * Ensure the printer is online. * Contact your administrator to check your Secure Function Lock settings.
What to do if my Brother 8085DN - DCP B/W Laser All in One Printer does not feed paper from the MP tray?
If your Brother All in One Printer is not feeding paper from the MP tray: * Fan the paper well and put it back in the tray firmly. * Make sure that MP tray mode is chosen in the printer driver.
Why is my Brother All in One Printer not printing on both sides even with Duplex setting?
If your Brother All in One Printer is not printing on both sides of the paper even though the printer driver setting is Duplex, check the paper size setting in the printer driver.
Why is my Brother All in One Printer printing unexpectedly or printing garbage?
If your Brother All in One Printer is printing unexpectedly or printing garbage, try the following: * Pull out the paper tray and wait for it to stop printing. * Check the settings in your application to ensure it's set up correctly for your printer. * If using a parallel port connection, verify the port is BRMFC and not LPT1.
How to fix Brother All in One Printer not printing over a wired network?
If you are unable to print over a wired network with your Brother All in One Printer: * Reconnect the LAN cable to the hub to ensure the cable and network connections are working. * If possible, try connecting the printer to a different port on your hub using a different cable.
How to fix OCR when it does not work on Brother All in One Printer?
Try increasing the scanning resolution.
What to do if the drum unit or toner cartridge is too hot in my Brother 8085DN - DCP B/W Laser?
If the drum unit or toner cartridge in your Brother All in One Printer is too hot: * Make sure that you can hear the fan in the machine spinning and that the exhaust outlet is not blocked. * If the fan is spinning, remove any obstacles around the exhaust outlet and leave the machine on but unused for several minutes. * If the fan isn't spinning, disconnect the machine from power for several minutes, then reconnect it.
Why are the printed pages from my Brother All in One Printer smeared?
Smeared printed pages from your Brother All in One Printer may occur if the Paper Type setting is incorrect for the print media you are using, or if the print media is too thick or has a rough surface.
How to remove vertical black line on copies from Brother All in One Printer?
Black vertical lines on copies from your Brother All in One Printer are typically caused by dirt or correction fluid on the glass strip, or a dirty corona wire. See Cleaning the scanner on page 94 and Cleaning the corona wire on page 96.
General| Printer Type | Laser |
|---|---|
| Functions | Print, Copy, Scan |
| Duplex Printing | Yes |
| Copy Resolution | Up to 600 x 600 dpi |
| Scanner Type | Flatbed, ADF |
| Memory | 32 MB |
| Operating System Compatibility | Windows, Mac, Linux |
| Scan Resolution | Up to 19200 x 19200 dpi (interpolated) |
| Paper Capacity | 250 sheets |
| Connectivity | Ethernet |
Explains how to use the Brother printer driver for Windows.
Step-by-step guide to print a document from your computer.
Instructions for printing on both sides of the paper.
Overview of configurable settings within the printer driver.
Accessing advanced options like scaling, watermarks, and security.
Details scanning using TWAIN and WIA drivers.
Steps to configure Windows Firewall for network connectivity.
Setting up the machine for network scanning on Macintosh.
To Next Page
