Brother MFC-9325CW User Manual

Safety and legal
119
A
24 Unplug this product from the mains power and telephone line sockets, and refer servicing to
qualified Service Personnel under the following conditions:
 If the power cord is damaged or frayed.
 If liquid has been spilled into the product.
 If the product has been exposed to rain or water.
 If the product does not operate normally when the operating instructions are followed.
Adjust only those controls that are covered by the operating instructions. Incorrect
adjustment of other controls may result in damage and will often require extensive work by
a qualified technician to restore the product to normal operation.
 If the product has been dropped or the casing has been damaged.
 If the product exhibits a distinct change in performance, indicating a need for service.
25 This unit will only work in conjunction with a tone signalling (DTMF) telephone, but some
telephones are not compatible. Since noise or speech from the telephone can upset dialling
from this unit, errors may result if the devices are used together in other than quiet conditions.
26 Where it is necessary to dial prefix digits, such as a Caller Display override code (“0196” or
“0197”), this unit will have to be used in conjunction with an associated tone signalling (DTMF)
telephone.
27 Note that some telephones are not compatible with this unit and dialling errors may result if the
two devices are used together in other than quiet conditions. The Telecom Faults Service is
not to be called should such problems arise. In such cases, it is recommended that the prefix
and wanted number are dialled manually.
28 This equipment may not provide for the effective hand-over of a call to another device
connected to the same line.
29 This equipment is not capable, under all operating conditions, of correct operation at the higher
speeds for which it is designed. Telecom will accept no responsibility should difficulties arise
in such circumstances. This condition typically applies to 56 kbit/s modems and facsimile
products operating at >14.4 kbit/s.
30 When using the Caller Line Identification incorporated in this device, verify the integrity of the
recorded digits prior to dialling.
31 Some parameters required for compliance with Telecom’s Telepermit requirements are
dependent on the equipment (PC) associated with this device. The associated equipment shall
be set to operate within the following limits for compliance with Telecom’s Specifications:
 There shall be no more than 10 call attempts to the same number within any 30 minute
period for any single manual call initiation, and
 The equipment shall go on-hook for a period of not less than 30 seconds between the end
of one attempt and the beginning of the next call attempt.
 Automatic calls to different numbers are spaced such that there is not less than 5 seconds
between the end of one call attempt and the beginning of another.
 Equipment shall be set to ensure that calls are answered within 3 and 30 seconds of the
receipt of ringing.

Brother MFC-9325CW Specifications

General

DVD/CD printing	No
Print technology	LED
Maximum resolution	2400 x 600 DPI
Economical printing	Yes
Print speed (black, normal quality, A4/US Letter)	19 ppm
Fax compatibility	ITU-T G3
Dimensions (WxDxH)	429.3 x 490.2 x 391.8 mm
All-in-one functions	Copy, Fax, Print, Scan
Connectivity technology	Wired & Wireless
Display number of colors	Monochrome
Color all-in-one functions	copy, fax, print, scan
Printing colors	Black, Cyan, Magenta, Yellow
Maximum duty cycle	25000 pages per month
Recommended duty cycle	1500 pages per month
Number of print cartridges	4
Page description languages	BR-Script 3, PCL 6
Copier resize	25 - 400 %
Maximum copy resolution	- DPI
Maximum number of copies	35 copies
N-in-1 copy function (N=)	2, 4
Copy speed (black, normal quality, A4)	19 cpm
Scan to	CIFS, E-mail, File, FTP, Image, OCR, USB
Scanner type	Flatbed scanner
Input color depth	48 bit
Maximum scan area	A4 / Letter (216 x 297) mm
Maximum scan resolution	19200 x 19200 DPI
Optical scanning resolution	1200 x 2400 DPI
Fax memory	600 pages
Modem speed	33.6 Kbit/s
Fax coding methods	JBIG, JPEG, MH, MMR (Fax coding method), MR
Fax transmission speed	2 sec/page
Paper input type	Paper tray
Total input capacity	250 sheets
Total output capacity	100 sheets
Total number of input trays	2
Multi-Purpose tray input capacity	1 sheets
Maximum print size	216 x 356 mm
Paper tray media types	Bond paper, Envelopes, Labels, Plain paper, Recycled paper
ISO A-series sizes (A0...A9)	A4, A5, A6
ISO B-series sizes (B0...B9)	B5
Maximum ISO A-series paper size	A4
Display	LCD
Market positioning	Business
Standard interfaces	Ethernet, USB 2.0, Wireless LAN
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Wi-Fi standards	802.11b, 802.11g
Supported network protocols (IPv4)	ARP, RARP, BOOTP, DHCP, APIPA(Auto IP), WINS/NetBIOS name resolution, DNS Resolver, mDNS, LLMNR responder, LPR/LPD, Custom Raw Port/Port9100, IPP/IPPS, FTP Client and ServerTELNET Server, HTTP/HTTPS server, TFTP client and server, SMTP Client, APOP, POP before SMTP, SMTP-AUTH, SNMPv1/v2c/v3, ICMP, LLTD responder, WebServicesPrint, CIFS Client, SNTP, SSL/TLS
Supported network protocols (IPv6)	NDP, RA, DNS resolver, mDNS, LLMNR responder, LPR/LPD, Custom Raw Port/Port9100, IPP/IPPS, FTP Client and Server, TELNET Server, HTTP/HTTPS server, TFTP client and server, SMTP Client, APOP, POP before SMTP, SMTP-AUTH, SNMPv1/v2c/v3, ICMPv6, LLTD responder, WebServicesPrint, CIFS Client, SNTP, SSL/TLS
Maximum internal memory	576 MB
Sound power level (standby)	30 dB
Sound pressure level (copying)	53 dB
AC input voltage	120 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	75 W
Power consumption (PowerSave)	12 W
Power consumption (average operating)	480 W
Package weight	28490 g
Operating relative humidity (H-H)	20 - 80 %