EasyManua.ls Logo

CAB XC Series - User Manual

CAB XC Series
30 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Label Printer
Operator's Manual
XC Series

Table of Contents

Other manuals for CAB XC Series

Preview: Service Manual
Service Manual37 pages

Questions and Answers

  • O
    osanchezAug 17, 2025
    What to do if display and navigator pad are not functioning on CAB XC?
    • A
      alan89Aug 17, 2025
      If your CAB Label Maker display and navigator pad are not working, and the LED1 is not illuminating, try replacing the CPU or the power supply unit. If the LED1 flashes, you may need to reload the firmware. Also, check the cable connection between the CPU and the control panel, and ensure the correct voltages are active at the 3.3V and 5V measurement points on the CPU. If these steps don't resolve the issue, consider replacing the LCD display or the PCB Navi Button.
  • D
    david16Aug 19, 2025
    How to fix communication issues on CAB Label Maker?
    • D
      Dan KingAug 19, 2025
      If communication via an interface is not functioning on your CAB Label Maker, first check whether the interface configurations of the printer and computer match. For an Ethernet connection, verify the IP address and subnet mask. Inspect the interface cable for any damage and replace it if necessary. If all interface functionality is lost, consider replacing the CPU.
  • T
    tdavisAug 22, 2025
    Why does my CAB XC Label Maker show a voltage error?
    • E
      Emily GonzalezAug 22, 2025
      If your CAB Label Maker is showing a voltage error, and the voltage of the battery on the CPU is too low, replace the CPU. If the motor voltage is too low, check the motor voltage at the measurement point V mot. If the voltage is too low, replace the power supply unit; if the voltage is correct, replace the CPU. If the 24 V is too low, check the voltage at measurement point +24V. If the voltage is too low, replace the power supply unit; if the voltage is correct, replace the CPU. If the 24 V at the peripheral connection is too low, disconnect the peripheral device. If the fault still exists, replace the CPU; if the fault is remedied, repair or replace the peripheral device.
  • C
    Connor CarrilloAug 25, 2025
    How to troubleshoot medium transport issues on CAB XC?
    • P
      Patty RomeroAug 25, 2025
      If the medium is not being transported in your CAB Label Maker, check the electrical connections between the CPU and the stepper motor media transport. Also, inspect the drive mechanism. If these checks do not resolve the issue, consider replacing the CPU or the stepper motor media transport.
  • J
    jeffreygarciaAug 28, 2025
    What to do if CAB XC Label Maker prints no image with medium transport?
    • J
      James HarmonAug 28, 2025
      If your CAB Label Maker is not printing an image with medium transport, check the plug connections at the printhead. Examine the printhead cable for any damage and replace it if necessary. At the lower printhead, check the ribbon saver adjustment. If the problem persists, replace the printhead or the CPU.
  • R
    Robin MedinaAug 30, 2025
    Why is my peripheral device not functioning with CAB XC Label Maker?
    • M
      Monica MorrisAug 30, 2025
      If a peripheral device is not functioning with your CAB Label Maker, first check whether the peripheral device is activated via programming. Then, check the USB cable of the peripheral device and replace it if necessary. Also, check the peripheral device itself. If the issue continues, consider replacing the CPU.
  • T
    Troy MaynardSep 2, 2025
    What to do if navigator pad is not functioning on CAB Label Maker?
    • A
      Ashley SmithSep 2, 2025
      If the navigator pad is not functioning, but the display is working on your CAB Label Maker, check the cable connection between the LCD Display and PCB Navi Button, and replace if necessary. If the issue persists, replace the PCB Navi Button or the LCD Display.
  • M
    Michael JacobsSep 4, 2025
    How to fix a non-functioning display on CAB Label Maker?
    • J
      Joseph MichaelSep 5, 2025
      If the display is not functioning, but the navigator pad is functioning on your CAB Label Maker, replace the LCD Display.
  • A
    Austin KellySep 7, 2025
    What causes ADC malfunction in CAB XC Label Maker?
    • T
      Tammy BrownSep 7, 2025
      If your CAB Label Maker is experiencing an ADC malfunction due to a fault on the CPU, replace the CPU.
  • J
    Julie SullivanSep 12, 2025
    What does invalid setup mean on CAB XC?
    • A
      Alicia JohnsonSep 12, 2025
      If your CAB Label Maker is showing an invalid setup due to a fault on the CPU, replace the CPU.

Summary

Introduction

Instructions

Explains the meaning of warning symbols used in the manual for safety and guidance.

Intended Use

Defines the printer's purpose and specifies improper usage to avoid risks and damage.

Safety Instructions

Crucial safety guidelines covering electrical, environmental, and operational hazards.

Environment

Tips for environmental protection and proper disposal of the printer and its components.

Installation

Device Overview

Identifies and illustrates all major components and parts of the label printer.

Unpacking and Setting-up the Printer

Step-by-step instructions for safely removing the printer from packaging and initial setup.

Connecting the Device

Details on connecting the printer to power sources and computer/network interfaces.

Switching on the Device

Procedures for powering on the printer and initiating its self-test sequence.

Control Panel

Control Panel Structure

Overview of the control panel's display, navigator pad, and integrated keys.

Symbol Displays

Explanation of various icons and symbols shown on the printer's display screen.

Printer States

Describes the different operational states (e.g., Ready, Printing, Pause) and their indicators.

Key Functions

Details the functionality of the control panel keys in different printer modes.

Loading Material

Loading Labels

Instructions for preparing the printer for label loading, including external rewinder setup.

Positioning the Label Roll on the Roll Retainer

Guide on how to correctly mount a label roll onto the printer's roll retainer.

Loading Fanfold Labels

Procedures for loading labels supplied in a fanfold format into the printer.

Inserting Labels into the Print Mechanics

Step-by-step guide for feeding labels into the printer's internal print mechanism.

Setting the Label Sensor

How to adjust the label sensor for accurate detection of label gaps or marks.

Setting the Head Locking Systems

Instructions for adjusting the head locking plungers for optimal print quality.

Loading Transfer Ribbon

Detailed instructions on how to load the transfer ribbon correctly for printing.

Setting the Feed Path of the Transfer Ribbon

Guidance on adjusting the ribbon path to prevent wrinkles and ensure smooth feeding.

Printing Operation

Printhead Protection

Essential precautions to prevent damage to the printheads during operation and handling.

Synchronization in Cut Mode

How to ensure correct label length and cutting by synchronizing print jobs.

Designing the Print Image with Direct Programming

Techniques for creating print images, especially for dual-color printing via direct programming.

Ribbon Saving

Explanation of the ribbon saver function to minimize transfer ribbon consumption.

Avoiding Loss of Material

Strategies to minimize waste of label material and transfer ribbon during printing.

Avoiding Loss of Data

Methods to prevent loss of print job data, especially during error conditions or material changes.

Cleaning

Cleaning Information

General maintenance guidelines and safety warnings before performing cleaning.

Cleaning the Print Rollers

Procedures for cleaning the print rollers to maintain media transport and print quality.

Cleaning the Printheads

Detailed instructions and safety precautions for cleaning the printer's sensitive printheads.

Fault Correction

Types of Errors

Categorizes printer errors into correctable, irrecoverable, and critical states.

Problem Solution

Lists common printer issues, their causes, and step-by-step remedies.

Error Messages and Fault Correction

Comprehensive guide to error messages, their meanings, and detailed solutions.

Media

Media Dimensions

Technical specifications detailing label and endless material dimensions for printer compatibility.

Device Dimensions

Provides key physical dimensions and measurement points of the printer for installation.

Reflex Mark Dimensions

Specifies requirements for reflex marks for media sensor detection.

Cut-out Mark Dimensions

Details specifications for cut-out marks used in media for gap sensor recognition.

Licences

EC Declaration of Conformity

Manufacturer's declaration of compliance with relevant European safety and health regulations.

FCC

Statement of compliance with Federal Communications Commission rules for digital devices.

CAB XC Series Specifications

General IconGeneral
BrandCAB
ModelXC Series
CategoryLabel Maker
LanguageEnglish

Related product manuals