Cabela's CB24ESC1 - User Manual

Questions and Answers

M
Makayla RiceAug 17, 2025
Why Cabela's CB24ESC1 digital control center has no power?
- M
  Michelle MccormickAug 17, 2025
  If the digital control center on your Cabela's Grill isn't lighting up, there are several potential causes. First, ensure the grill is properly connected to a working power source and that the breaker hasn't tripped. Also, check that the GFCI is a minimum 10 Amp service. Make sure all wire connections are firmly connected and dry. It may be as simple as pressing the power button, and holding it for two seconds. If that doesn't work, the fuse on the control board might be blown, remove the hopper access panel and check the fuse for a broken or blackened wire, and replace if necessary. In some cases, the GFCI outlet may have been tripped. If none of these steps work, the digital control center may be faulty and needs replacement.
K
Kristi HurstAug 20, 2025
What to do if Cabela's Grill fire in burn pot will not light?
- Q
  qcolemanAug 20, 2025
  If the fire in the burn pot of your Cabela's Grill won't light, it could be due to a few reasons. The auger might not be primed, especially if it's the first time using the grill or the hopper was completely emptied. In this case, you need to follow the Hopper Priming Procedure. Another cause could be a jammed auger motor. Inspect the auger tube for any visible damage or pellet jams. If nothing is visible, inspect the auger motor through the hopper access panel, to ensure the auger motor bracket is not damaged. Finally, the igniter itself might have failed. Visually confirm if the igniter is working by placing your hand above the burn pot and feeling for heat. If not, follow the Manual Start-up Procedure.
K
Kathryn WillisAug 23, 2025
Why Cabela's CB24ESC1 will not maintain stable temperature?
- M
  Manuel FreemanAug 23, 2025
  If your Cabela's Grill isn't maintaining a stable temperature, several factors could be responsible. First, check the burn pot for ash build-up or obstructions, and ensure the fan is working properly with no blockage in the air intake. Also, check the auger motor to confirm operation, and ensure there is no blockage in the auger tube. Next, ensure you're using sufficient, good-quality fuel and that there are no obstructions in the feed system. Finally, inspect the grill temperature probe and clean it if dirty. After checking these start the grill, set temperature to SMOKE and wait for 10 minutes. Check that the flame produced is bright and vibrant.
E
Ethan GainesAug 26, 2025
What does Er1 error code mean on Cabela's CB24ESC1 Grill?
- G
  gcarrAug 26, 2025
  The "Er1" error code on your Cabela's Grill indicates that the temperature probe isn't making a connection. Check the grill probe for any visible damage. Also, unplug the unit and remove the hopper access panel to locate the black wires of the temperature probe. Disconnect the spade connectors, then reconnect until it clicks. Additionally, ensure the probe wire connections are firmly connected and correctly connected to the digital control board.
D
daniel92Aug 28, 2025
Why Cabela's CB24ESC1 produces too much smoke?
- R
  Russell CruzAug 28, 2025
  Excessive or discolored smoke from your Cabela's Grill can stem from several issues. Start by checking for grease build-up. Also, the wood pellets might be moist or of poor quality, remove moist wood pellets from hopper and replace with dry ones. Another potential cause is a blocked burn grate, clear burn pot of moist wood pellets. Finally, ensure the fan has sufficient air intake and isn't blocked.
M
Mrs. Julia GriffinAug 31, 2025
How to prevent flare ups on Cabela's CB24ESC1 Grill?
- T
  Tracy OrtegaAug 31, 2025
  Frequent flare-ups on your Cabela's Grill can often be reduced by attempting to cook at a lower temperature, because grease has a flash point. Also, check for grease build-up and clean if necessary. If you're cooking with the flame broiler open, try closing it for indirect flame cooking.
C
Crystal FoxSep 2, 2025
What does ErH error code mean on Cabela's CB24ESC1?
- H
  Heather GouldSep 2, 2025
  The “ErH” error code on a Cabela's Grill indicates that the unit has overheated, possibly due to a grease fire or excess fuel. Turn the unit off and allow it to cool. After it cools, remove pellets and confirm the positioning of all component parts. Once cooled, turn the unit back on and select the desired temperature.
K
Kaylee RussellSep 5, 2025
What does Err error code mean on Cabela's CB24ESC1 Grill?
- A
  april84Sep 5, 2025
  The “Err” error code on your Cabela's Grill indicates a power interruption occurred during operation, preventing the grill from completing its cool-down cycle. Check the power supply. Turn the unit off, wait two minutes, and then turn it back on.
J
Jerry CooperSep 8, 2025
Why Cabela's CB24ESC1 temperature readout won't adjust?
- P
  Paul CraigSep 8, 2025
  If the actual temperature readout on your Cabela's Grill isn't adjusting, the grill probe may be dirty. Also, the grill probe wire might be wet, in that case use a hair dryer to dry the wires.
R
richardcarrollSep 12, 2025
How to change temperature units on Cabela's CB24ESC1?
- B
  Bobby ColemanSep 12, 2025
  If the LCD display on your Cabela's Grill has the wrong readout, the temperature setting switch might not be set correctly to read ºC or ºF. Disconnect the unit from the power source. Remove the hopper access panel to access the back of the Digital Control Center. Use a small flashlight to find the temperature setting switch, located near the center of the back of the Digital Control Center. Flip the switch to ºC (Celsius) or to ºF (Fahrenheit), as preferred. Replace hopper access panel.