To Next PageTo Next Page
Need help?Do you have a question about the CAME ZLX24MA and is the answer not in the manual?
General| Brand | CAME |
|---|---|
| Model | ZLX24MA |
| Category | Control Panel |
| Language | English |
Identification of the ZLX24M control board, including model numbers.
Component description for the control board holder.
Description of the terminal block that includes a fuse compartment.
Identification of the 4 Ampere fuse for the 120V power line.
Identification of the 3.15 Ampere fuse for the 230V power line.
Description of the two provided 2-pole terminal blocks.
Locating and identifying the fuse for accessories.
Locating and identifying the main control board fuse.
Terminal board for connecting the power supply to the control board.
Terminal board used for connecting signalling devices.
Terminal board for connecting control devices.
Identification of the control board's integrated display.
Terminal board for connecting safety devices.
Connector for the memory roll card on the control board.
Connector for the CAME KEY accessory.
Connector for the RIO CONN card.
Terminal board for connecting to CRP systems.
Connector for the RSE card.
Terminal board for connecting the antenna.
Connector for plug-in radio frequency cards (AF).
Layout and identification of programming buttons on the board.
Terminal board for connecting devices via the BUS system.
Terminal boards for micro limit switches and/or encoders.
Terminal board for gearmotor connection with encoder or slowdown.
Identifying the fixing point for the control board support.
Identifying the fixing point for the fuse holder terminal block.
Wiring diagram for connecting gearmotors with a slowdown microswitch.
Wiring diagram for connecting gearmotors with limit-switch/slowdown microswitches.
Connection details for the STOP button (Normally Closed contact).
Connection for a control device with OPEN ONLY function (Normally Open).
Connection for a control device for partial or pedestrian opening (NO).
Connection for a control device with CLOSE ONLY function (Normally Open).
Connection for a control device with OPEN-CLOSE function (Normally Open).
Wiring the antenna to the control panel.
Wiring and installation of the flashing beacon.
Wiring and installation of the additional light.
Wiring and installation of the operator status warning light.
Standard connection diagram for DELTA photocells.
Wiring diagram for DELTA photocells with safety test.
Standard connection diagram for DIR/DELTA-S photocells.
Wiring diagram for DIR/DELTA-S photocells with safety test.
Standard connection diagram for DXR/DLX photocells.
Wiring diagram for DXR/DLX photocells with safety test.
Connection diagram for the DFWN sensitive edge.
Details on the function and operation of the ESC button.
Details on the function and operation of the navigation buttons.
Details on the function and operation of the ENTER button.
Guidance on initiating the programming sequence.
Configuration parameter for selecting the motor type.
Parameter to set the total number of motors connected.
Procedure for testing the motor operation.
Configuration of the CX input.
Configuration of the CY input.
Setting the limit-switch function for motor operation.
Setting the input type for FC/FA connections.
Configuration parameter for motor power output.
Procedure for calibrating the motor travel limits.
Configuration parameter for selecting the motor type.
Parameter to set the total number of motors connected.
Procedure for testing the motor operation.
Configuration of the CX input.
Configuration of the CY input.
Setting the limit-switch function for motor operation.
Setting the input type for FC/FA connections.
Configuration parameter for motor power output.
Setting motor approach points for opening and closing.
Control parameter for slowdown AST.
Procedure for calibrating the motor travel limits.
Configuration of the total stop function.
Setting the function for the CX input.
Setting the function for the CY input.
Performing a test of safety devices.
Configuration of the hold-to-run operating mode.
Setting the command sequence mode (step-by-step/sequential).
Configuration for the gate open warning light behavior.
Enabling or disabling the encoder function.
Adjusting the thrust force during closing.
Enabling or disabling thrust control.
Configuration for the electric lock operation.
Control settings for the additional light.
Setting the automatic closure delay time.
Auto-closing settings after partial or pedestrian opening.
Setting the duration of the pre-flashing signal.
Setting the delay time for M1 opening.
Setting the delay time for M2 closing.
Setting the duration for courtesy light operation.
Adjusting the opening and closing speed for M2 leaf.
Setting the slowdown speed for M1 leaf opening/closing.
Setting the slowdown speed for M2 leaf opening/closing.
Control parameter for Travel AST function.
Control parameter for Slowdown AST function.
Adjusting the partial opening function settings.
Setting the slowdown point for M1 opening.
Setting the slowdown point for M1 closing.
Setting the approach point for M1 opening.
Setting the approach point for M1 closing.
Setting the slowdown point for M2 opening.
Setting the slowdown point for M2 closing.
Setting the approach point for M2 opening.
Setting the approach point for M2 closing.
Configuration for reducing motor speed.
Parameter to configure the number of motors.
Function to save system data.
Function to read system data.
Setting the CRP address.
Configuring maintenance alerts and settings.
Setting the speed for RSE communication.
Reconfiguring the limit-switch function.
Reconfiguring the FC/FA input type.
Settings for obstacle detection and removal.
Procedure for adding a new user.
Procedure for removing a single user.
Procedure for removing all registered users.
Settings for radio decoding (all, rolling code, TW key).
Configuration for self-learning rolling code.
Selecting the motor type from a list.
Procedure for performing a motor test.
Procedure for calibrating travel limits.
Function to reset system parameters.
Displaying total and partial manoeuvre counts.
Configuring the power output for the motor.
Showing the firmware version of the control board.
Enabling or disabling the password protection feature.
Steps to recover access if the password is lost.
Procedure to reset the control board to factory default settings.
Using a memory roll for data and configuration transfer.
Saving user data and configurations to a memory roll.
Loading user data and configurations from a memory roll.
Description of error E1: Motor M1 calibration failure.
Description of error E2: Motor M2 calibration failure.
Description of error E3: Encoder signal not received.
Description of error E4: Service test procedure failed.
Description of error E7: Error related to operating time.
Description of error E9: Repeated obstacles during closing.
Description of error E10: Repeated obstacles during opening.
Description of error E11: Exceeded maximum obstacle count.
Description of error E12: Motor power supply voltage problem.
Description of error E13: Limit switch input error.
Description of error E15: Transmitter is incompatible.
Description of error E17: Wireless system communication fault.
Description of error E18: Wireless system requires configuration.
Description of error E24: Communication error with BUS device.
Description of error E25: Incorrect BUS address settings.
