Canon imageRUNNER ADVANCE C3530i III Service Manual

E490-9999-04 Error due to the reader for different model
Detection Description Configuration mismatch between the Reader Controller software and the Reader/DADF was
detected.
Remedy
Execute automatic software update.
(Install the system software with correct configuration.)
E500-0000-02 Communication error (Finisher-K1/Sorter-A1)
Detection Description a. A communication error between the host machine and the Finisher was detected.
b. A communication error between the host machine and the Sorter was detected.
Remedy
a. INNER FIN-K1
[Related parts]
- Harnesses and connectors from the DC Controller PCB to the Finisher Controller PCB
- Finisher Controller PCB (PCB1)
- DC Controller PCB
[Remedy] Perform the following in the order while checking whether the error is cleared.
1. Check/replace the harness and connector between the DC Controller PCB and the Finisher
Controller PCB.
2. Replace the Finisher Controller PCB.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when
Replacing the Parts" in the Service Manual.
3. Replace the DC Controller PCB.
b SORTER-A1
[Related parts]
- Harnesses and connectors from the DC Controller PCB to the Sorter Controller PCB
- Sorter Controller PCB (PCB1)
- DC Controller PCB
[Remedy] Perform the following in the order while checking whether the error is cleared.
1. Check/replace the harness and connector between the DC Controller PCB and the Sorter
Controller PCB.
2. Replace the Sorter Controller PCB.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when
Replacing the Parts" in the Service Manual.
3. Replace the DC Controller PCB.
[Reference] Before replacing the DC Controller PCB, back up the service mode data and restore
the backup data after the replacement so the data may be able to be protected.
- Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP
- Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
E501-0000-02 Communication error (Finisher-AA1)
Detection Description A communication error between the host machine and the Finisher was detected.
Remedy
STAPLE FIN-AA1/BOOKLET FIN-AA1
[Related parts]
- Harnesses and connectors from the DC Controller PCB to the Finisher Controller PCB
- Finisher Controller PCB (PCB1)
- DC Controller PCB
[Remedy] Perform the following in the order while checking whether the error is cleared.
1. Check/replace the harness and connector between the DC Controller PCB and the Finisher
Controller PCB.
2. Replace the Finisher Controller PCB.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when
Replacing the Parts" in the Service Manual.
3. Replace the DC Controller PCB.
[Reference] Before replacing the DC Controller PCB, back up the service mode data and restore
the backup data after the replacement so the data may be able to be protected.
- Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP
- Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
7. Error/Jam/Alarm
388

Canon imageRUNNER ADVANCE C3530i III Specifications

General

Print Resolution	1200 x 1200 dpi
Interface	USB 2.0, Ethernet, Wi-Fi
Output Paper Capacity	250 sheets
Duplex Printing	Yes
Copy Resolution	600 x 600 dpi
Multiple Copies	Up to 999 copies
Magnification	25% - 400% (1% Increments)
Scan Resolution	600 x 600 dpi
Fax	Optional
Fax Resolution	400 x 400 dpi
Power Consumption (Maximum)	1.5 kW
Type	Color Laser
Functions	Print, Copy, Scan, Send, Store
First Print Out Time	5.9 seconds or less
Processor Speed	1.75 GHz
Memory	3.0 GB RAM
Hard Disk Drive	320 GB
Supported Media Types	Plain, Heavy, Recycled, Color, Label, Envelope
Supported Media Sizes	A3, A4, A5, B4, B5, Legal, Letter, Executive
Supported Media Weights	52-220 gsm
Pull Scan	Yes
Send Resolution	200 x 200 dpi, 300 x 300 dpi, 400 x 400 dpi, 600 x 600 dpi
Display	10.1-inch TFT LCD WSVGA Color Touch Panel
Mobile Printing	Available