210
APPENDIX G — OPTIONAL GREENSPEED/LOW AMBIENT CONTROL (cont)
The interface wiring for the VFDs is shown in Fig. A. Terminal
designations are shown in the Terminal Designation table (see
Table O). Configurations are shown in the VFD Parameters ta-
bles, Tables P-U.
Table O — VFD Terminal Designations
Table P — ACS320 VFD Greenspeed Parameters Tables, Part 1
CAUTION
UNIT DAMAGE HAZARD
It is strongly recommended that the user NOT change any
programming without consulting Carrier service personnel.
Unit damage may occur from improper programming.
TERMINAL FUNCTION
U1
Three-Phase Main Circuit Input Power SupplyV1
W1
U2
Three-Phase AC Output to Motor, 0 V to
Maximum Input Voltage Level
V2
W2
10(GND)
Factory-supplied jumper
12 (COMMON)
9 (24 VDC)
Run (factory-supplied jumper)
11 (DI-1)
9 (24 VDC) Start Enable 1 (factory-supplied jumper). When
11 (DI-4) opened the drive goes to emergency stop.
13 (AI-1)
Factory wired for 24 Vdc input from Fan Speed Board
14 (AGND)
LOOKUP VARIABLE
ABB ACS320 VFD
PARAMETER ID :
48EJ000329-DATA 48EJ000357-DATA 48EJ000379-DATA 48EJ000376-DATA 48EJ000331-DATA 48EJ000335-DATA
PKG
48EJ000329 48EJ000357 48EJ000379 48EJ000376 48EJ000331 48EJ000335
Motor Part Number
HD52AR228 HD52AR228 00PG000007207A HD52AR228 HD52AR381 HD52AR381
VFD Part Number
HK30WA523 HK30WA523 HK30WA523 HK30WA524 HK30WA532 HK30WA532
Drive HP
3 3 3 7.5 7.5 7.5
Number of Motors
222322
LANGUAGE
9901 English (0) English (0) English (0) English (0) English (0) English (0)
APPLIC MACRO
9902 HVAC (1) HVAC (1) HVAC (1) HVAC (1) HVAC (1) HVAC (1)
MOTOR CTRL MODE
9904 SCALAR: FREQ SCALAR: FREQ SCALAR: FREQ SCALAR: FREQ SCALAR: FREQ SCALAR: FREQ
VOLTAGE
9905 230 230 230 230 380 380
N. AMPS
9906 12 12 11.6 18 7.8 7.8
MOTOR NOM FREQ
9907 60Hz 60Hz 60Hz 60Hz 60Hz 60Hz
N. RPM
9908 850 850 850 850 850 850
N. HP
9909 555555
EXT1 COMMANDS
1001 DI1 (1) DI1 (1) DI1 (1) DI1 (1) DI1 (1) DI1 (1)
DIRECTION
1003 Forward (1) Forward (1) Forward (1) Forward (1) Forward (1) Forward (1)
REF1 SELECT
1103 COMM (8) COMM (8) COMM (8) COMM (8) COMM (8) COMM (8)
CONST SPEED SEL
1201 NOT SEL NOT SEL NOT SEL NOT SEL NOT SEL NOT SEL
CONST SPEED 7
1208 0 Hz 0 Hz 0 Hz 0 Hz 0 Hz 0 Hz
RELAY OUT 1
1401 Ready (1) Ready (1) Ready (1) Ready (1) Ready (1) Ready (1)
RELAY OUTPUT2
1402 Run (2) Run (2) Run (2) Run (2) Run (2) Run (2)
RELAY OUT 3
1403 FAULT (-1) FAULT (-1) FAULT (-1) FAULT (-1) FAULT (-1) FAULT (-1)
RUN ENABLE
1601 000000
START ENABLE 1
1608 DI4 (4) DI4 (4) DI4 (4) DI4 (4) DI4 (4) DI4 (4)
Parameter View
1611 333333
MAX AMPS
2003 21.0 21.0 20.3 31.5 13.7 13.7
MIN FREQ
2007 0Hz0Hz0Hz0Hz0Hz0Hz
MAX FREQ
2008 60Hz 60Hz 60Hz 60Hz 60Hz 60Hz
SWITCH FREQ
2606 4kHz 4kHz 4kHz 4kHz 4kHz 4kHz
START FCN
2101 Auto Auto Auto Auto Auto Auto
STOP FCN
2102 (1) Coast (1) Coast (1) Coast (1) Coast (1) Coast (1) Coast
ACCEL/DECEL
2201 Not Sel Not Sel Not Sel Not Sel Not Sel Not Sel
ACCEL
2202 30s 30s 30s 30s 30s 30s
DECEL
2203 30s 30s 30s 30s 30s 30s
IR COMP VOLT
2603 000000
COMM FAULT FUNC
3018 Last SP (3) Last SP (3) Last SP (3) Last SP (3) Last SP (3) Last SP (3)
COMM FAULT TIME
3019 10 s 10 s 10 s 10 s 10 s 10 s
COMM PROT SEL
9802 LEN(6) LEN(6) LEN(6) LEN(6) LEN(6) LEN(6)
TRIAL TIME
3102 300.0s 300.0s 300.0s 300.0s 300.0s 300.0s
DELAY TIME
3103 6.0s 6.0s 6.0s 6.0s 6.0s 6.0s
AR OVERCURRENT
3104 (1) Enable (1) Enable (1) Enable (1) Enable (1) Enable (1) Enable
EFB PROTOCOL ID
5301 0601 hex 0601 hex 0601 hex 0601 hex 0601 hex 0601 hex
EFB STATION ID
5302 43/44 43/44 43/44 43/44 43/44 43/44
EFB BAUD RATE
5303 38.4 kb/s 38.4 kb/s 38.4 kb/s 38.4 kb/s 38.4 kb/s 38.4 kb/s
EFB PARITY
5304 8 NONE 1 8 NONE 1 8 NONE 1 8 NONE 1 8 NONE 1 8 NONE 1
EFB CTRL PROFILE
5305 DCU PROFILE DCU PROFILE DCU PROFILE DCU PROFILE DCU PROFILE DCU PROFILE
To Next Page
Loading...
