Casio XJ-UT310WN User Manual

14
To select the input source
1. Press the [INPUT] key. This will display the “Input” dialog box.
2. Depending on the input source, perform one of the operations described in the
table below.
z The name of the input source you selected will appear in the upper right corner of the
projection screen for a few seconds.
z The message “No signal input” will appear if no input signal can be detected.
Note
z For more information about the operation required to select Network, USB Display, File
Viewer, or CASIO USB Tool as the input source and perform projection, refer to the following.
Resolution
The projector’s video resolution is fixed at WXGA (1280 × 800 pixels). Images may appear coarse, text
and other figures may be difficult to read or a moire pattern may appear when the input signal from a
computer does not match the projector’s video resolution. If this happens, try doing the following.
z Change the computer’s output resolution setting so it matches the projector’s video resolution.
For information about the video resolution of your projector, see “Specifications” in the Setup
Guide. See the user documentation that comes with your computer for details about changing its
settings.
z Change the “Aspect Ratio” setting to “True”. With the “True” setting, the projector projects the input
signal at its actual size (1 input source dot equal to one projector output pixel dot).
For information about configuring the Aspect Ratio setting, see “To change the aspect ratio of the
projected image (ASPECT)” (page 49).
To select this input source: Perform this operation:
Computer 1, Computer 2, Video,
S-Video, HDMI, Network, USB Display
Use the [T] and [S] keys to select the name of the input source you
want to select and then press the [ENTER] key.
File Viewer 1. Use the [T] and [S] keys to select “Viewer” and then press the
[ENTER] key.
2. On the dialog box that appears, confirm that “File Viewer” is
selected and then press the [ENTER] key.
CASIO USB Tool 1. Use the [T] and [S] keys to select “Viewer” and then press the
[ENTER] key.
2. Press the [T] key to select “CASIO USB Tool” and then press the
[ENTER] key.
Network: Separate Network Function Guide
USB Display: “Projecting with the USB Display Function” (page 41)
File Viewer: “Projecting with File Viewer” (page 17)
CASIO USB Tool: “Projecting the Screen Image of a Graphing Calculator” (page 46)

Casio XJ-UT310WN Specifications

General

Matrix size	0.65 \
Matrix type	3-panel (p-Si TFT active)
Number of colors	16.78 million colors
Native aspect ratio	16:10
Projection distance	- m
Projection technology	DLP
Supported aspect ratios	16:9, 16:10
Contrast ratio (typical)	1800:1
Screen size compatibility	50 - 110 \
Projector native resolution	WXGA (1280x800)
Keystone correction, horizontal	-5 - 5 °
Focus	Manual
Offset	118 %
Throw ratio	0.28:1
Focal length range	- mm
Light source type	Laser/LED hybrid
Service life of light source	20000 h
Full HD	No
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC, PAL, PAL 60, PAL M, PAL N, SECAM
Microphone in	Yes
Audio (L/R) in	2
USB connector type	USB Type-A, USB Type-B
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
VGA (D-Sub) ports quantity	3
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Noise level	34 dB
Noise level (economic mode)	29 dB
RMS rated power	16 W
Placement	Desktop, Ceiling
Product type	Ultra short throw projector
Product color	Grey, White
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.4 W
Power consumption (typical)	230 W
Operating altitude	0 - 3000 m
Operating temperature (T-T)	5 - 35 °C
Operating relative humidity (H-H)	20 - 80 %

Weight and Dimensions

Depth	332 mm
Width	414 mm
Height	152.4 mm
Weight	5500 g
Package depth	470 mm
Package width	594 mm
Package height	274 mm
Package weight	9620 g