Casio XJ-UT310WN User Manual

15
Your projector supports projection of 3D images. To project a 3D image, first enter the projector’s 3D
input mode, and then select the input source.
Important!
z Separately available 3D glasses (YA-G30) are required in order to view a projected 3D image in
3D.
z Separately available special software (CASIO 3D Converter) is required to project a 3D image
with the projector when a computer (analog RGB) is the input source.
z 3D image projection is not supported via an HDMI connection or component video
connection.
The input sources described below can be selected for projection in the 3D Input Mode.
Note
See “3D Signals (3D Input Mode)” (page 80) for a list of 3D image signals supported by this
projector.
Entering the 3D Input Mode
1. Press the [INPUT] key to display the input source selection screen.
2. Select Computer 1 (RGB), Computer 2 (RGB), S-video, or Video as the input
source.
3. Use the [T] and [S] keys to move the highlighting to “To 3D input mode” and
then press the [ENTER] key.
z This enters the 3D input mode and closes the input source selection screen.
Important!
z You cannot select HDMI, File Viewer, CASIO USB Tool, Network, or USB Display as the input
source in the 3D input mode. To use either of these input sources, change the input source
setting back to normal input mode.
z When Computer 1 (or Computer 2) is selected as the input source in the 3D input mode, a
component video signal input through the projector’s COMPUTER IN 1 (or COMPUTER IN 2)
terminal is treated as an RGB signal resulting in abnormal image projection.
z Except when using the projector for 3D image projection, you should normally leave it in the
normal input mode.
3D Input Mode
Input Source Projection Conditions
Computer (Analog RGB) z Any of the following types of 3D image data played back using separately available
special software (CASIO 3D Converter).
– 2D image file converted to a 3D image file using CASIO 3D Converter
– Side-by-side 3D format files
z Signal with 60Hz/120Hz vertical scan frequency
Composite Video, S-video z Field sequential 3D format files recorded with field sequential DVD software, etc.
z Signal with 60Hz vertical scan frequency

Casio XJ-UT310WN Specifications

General

Matrix size	0.65 \
Matrix type	3-panel (p-Si TFT active)
Number of colors	16.78 million colors
Native aspect ratio	16:10
Projection distance	- m
Projection technology	DLP
Supported aspect ratios	16:9, 16:10
Contrast ratio (typical)	1800:1
Screen size compatibility	50 - 110 \
Projector native resolution	WXGA (1280x800)
Keystone correction, horizontal	-5 - 5 °
Focus	Manual
Offset	118 %
Throw ratio	0.28:1
Focal length range	- mm
Light source type	Laser/LED hybrid
Service life of light source	20000 h
Full HD	No
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC, PAL, PAL 60, PAL M, PAL N, SECAM
Microphone in	Yes
Audio (L/R) in	2
USB connector type	USB Type-A, USB Type-B
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
VGA (D-Sub) ports quantity	3
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Noise level	34 dB
Noise level (economic mode)	29 dB
RMS rated power	16 W
Placement	Desktop, Ceiling
Product type	Ultra short throw projector
Product color	Grey, White
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.4 W
Power consumption (typical)	230 W
Operating altitude	0 - 3000 m
Operating temperature (T-T)	5 - 35 °C
Operating relative humidity (H-H)	20 - 80 %

Weight and Dimensions

Depth	332 mm
Width	414 mm
Height	152.4 mm
Weight	5500 g
Package depth	470 mm
Package width	594 mm
Package height	274 mm
Package weight	9620 g