Casio XJ-UT310WN User Manual

68
Warning messages and indicators let you know what the problem is when a projector error occurs.
z When an error occurs, wait until the fan stops before unplugging the AC power cord. If you unplug
the AC power cord while the fan is still operating, an error may occur when you plug the AC power
cord back in.
z Press the [ESC] key to clear the warning message.
Error Indicators and Warning Messages
Indicator/Error Message Description and Required Action
POWER : Green steady The projector’s internal temperature is very high. Perform the following
steps.
1 Check for any blocking of the projector’s intake vents and exhaust
vents, and make sure that there is sufficient space around the
projector. See
“Setup Precautions” (page 9).
2 If there is dust accumulated around the intake vents and/or exhaust
vents, turn off the projector and remove it. See
“Cleaning the
Projector” (page 66).
LIGHT : –
TEMP : –
Message : Internal temperature is too
high. Check projector air
vents for blockage.
POWER : Green steady J
Red steady
Power has turned off automatically due to internal overheating. Perform
the following steps.
1 Check for any blocking of the projector’s intake vents and exhaust
vents, and make sure that there is sufficient space around the
projector. See
“Setup Precautions” (page 9).
2 If there is dust accumulated around the intake vents and/or exhaust
vents, remove it. See
“Cleaning the Projector” (page 66).
If there is no problem with the projector’s vents, confirm that the POWER/
STANDBY indicator is lit red (without flashing), and then turn power back
on again. If the error occurs again when you turn power back on, contact
your retailer or nearest authorized CASIO Service Center.
LIGHT : –
TEMP : –
Message : Internal temperature is too
high. The projector will
turn off.
POWER : Red steady Power has turned off automatically due to a fan problem. Confirm that the
POWER/STANDBY indicator is lit red (without flashing) and that the fan
has stopped. After checking the POWER/STANDBY indicator, disconnect
the power cord from the projector and wait for all of the projector’s
indicators to go out. Next, reconnect the power cord and turn projector
power back on.
If the error occurs again when you turn power back on, contact your
retailer or nearest authorized CASIO Service Center.
LIGHT : Red steady
TEMP : Red steady
Message : There is a problem with
the fan. The projector will
turn off.
POWER : Red steady Power has turned off automatically due to a system problem. After
confirming that the POWER/STANDBY indicator is lit red (without
flashing), disconnect the power cord from the projector and wait for all of
the projector’s indicators to go out. Next, reconnect the power cord and
turn the projector back on.
If the error occurs again when you turn power back on, contact your
retailer or nearest authorized CASIO Service Center.
LIGHT : –
TEMP : Red steady
Message : A system problem has
occurred. The projector
will turn off.
POWER : Green steady A system problem has occurred, which may cause problems with some
functions. Turn off the projector, disconnect the power cord from the
projector and wait for all of the projector’s indicators to go out. Next,
reconnect the power cord and turn the projector back on.
If the error occurs again when you turn power back on, contact your
retailer or nearest authorized CASIO Service Center.
LIGHT : –
TEMP : –
Message : There is some problem
with the system.
The audio function may
not operate correctly.

Casio XJ-UT310WN Specifications

General

Matrix size	0.65 \
Matrix type	3-panel (p-Si TFT active)
Number of colors	16.78 million colors
Native aspect ratio	16:10
Projection distance	- m
Projection technology	DLP
Supported aspect ratios	16:9, 16:10
Contrast ratio (typical)	1800:1
Screen size compatibility	50 - 110 \
Projector native resolution	WXGA (1280x800)
Keystone correction, horizontal	-5 - 5 °
Focus	Manual
Offset	118 %
Throw ratio	0.28:1
Focal length range	- mm
Light source type	Laser/LED hybrid
Service life of light source	20000 h
Full HD	No
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC, PAL, PAL 60, PAL M, PAL N, SECAM
Microphone in	Yes
Audio (L/R) in	2
USB connector type	USB Type-A, USB Type-B
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
VGA (D-Sub) ports quantity	3
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Noise level	34 dB
Noise level (economic mode)	29 dB
RMS rated power	16 W
Placement	Desktop, Ceiling
Product type	Ultra short throw projector
Product color	Grey, White
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.4 W
Power consumption (typical)	230 W
Operating altitude	0 - 3000 m
Operating temperature (T-T)	5 - 35 °C
Operating relative humidity (H-H)	20 - 80 %

Weight and Dimensions

Depth	332 mm
Width	414 mm
Height	152.4 mm
Weight	5500 g
Package depth	470 mm
Package width	594 mm
Package height	274 mm
Package weight	9620 g