Cisco EX90 - Adding Participants to Calls; Adding Participants to an Ongoing Call

44
Cisco TelePresence System EX90/EX60 Administrator guide
D14726.03 Cisco TelePresence System EX90-EX60 Administrator Guide TC4.0, December 2010.
Copyright © 2010 Cisco Systems, Inc. All rights reserved.
www.cisco.com
Advanced conguration
SIP Prole [1..1] Type
Enables SIP extensions and special behavior for a vendor or provider.
Requires user role: ADMIN
Value space: <Standard/Alcatel/Avaya/Cisco/Microsoft/Nortel/Experimental/Siemens>
Standard: Should be used when registering to standard SIP proxy like OpenSer.
Alcatel: Must be used when registering to a Alcatel-Lucent OmniPCX Enterprise R7 or later.
Avaya: Must be used when registering to a Avaya Communication Manager.
Cisco: Must be used when registering to a Cisco CallManager version 5 or later.
Microsoft: Must be used when registering to a Microsoft LCS or OCS server.
Nortel: Must be used when registering to a Nortel MCS 5100 or MCS 5200 PBX.
Experimental: Can be used if auto is not working. Note: This mode is for testing purposes only.
Ex a m ple: SIP Prole 1 Type: Standard
SIP Prole [1..1] Outbound
The client initiated connections mechanism for rewall traversal, connection reuse and redundancy.
The current version supports http://tools.ietf.org/html/draft-ietf-sip-outbound-20.
Requires user role: ADMIN
Value space: <On/O>
On: Set up multiple outbound connections to servers in the Proxy Address list.
O: Connect to the single proxy congured rst in Proxy Address list.
Ex a m ple: SIP Prole 1 Outbound: Off
SIP Prole [1..1] Proxy [1..4] Discovery
Select if the SIP Proxy address is to be obtained manually or by using Dynamic Host Conguration
Protocol (DHCP).
Requires user role: ADMIN
Value space: <Auto/Manual>
Manual: When Manual is selected, the manually congured SIP Proxy address will be used.
Auto: When Auto is selected, the SIP Proxy address is obtained using Dynamic Host Conguration
Protocol (DHCP).
Ex a m ple: SIP Prole 1 Proxy 1 Discovery: Manual
SIP Prole [1..1] Proxy [1..4] Address
The Proxy Address is the manually congured address for the outbound proxy. It is possible to use a
fully qualied domain name, or an IP address. The default port is 5060 for TCP and UDP but another
one can be provided. If Outbound is enabled, multiple proxies can be addressed.
Requires user role: ADMIN
Value space: <S: 0, 255>
Format: Compact string with a maximum of 255 characters. An IP address that contains letters
(192.a.2.0) or unvalid IP addresses (192.0.1234.0) will be rejected.
Ex a m ple: SIP Prole 1 Proxy 1 Address: ""
SIP Prole [1..1] Authentication [1..1] LoginName
This is the user name part of the credentials used to authenticate towards the SIP proxy.
Requires user role: ADMIN
Value space: <S: 0, 50>
Format: String with a maximum of 50 characters.
Ex a m ple: SIP Prole 1 Authentication 1 LoginName: ""
SIP Prole [1..1] Authentication [1..1] Password
This is the password part of the credentials used to authenticate towards the SIP proxy.
Requires user role: ADMIN
Value space: <S: 0, 50>
Format: String with a maximum of 50 characters.
Ex a m ple: SIP Prole 1 Authentication 1 Password:
The SIP settings, cont...The SIP settings, cont...