Need help?Do you have a question about the COBHAM AVIATOR UAV 200 and is the answer not in the manual?
General| Brand | COBHAM |
|---|---|
| Model | AVIATOR UAV 200 |
| Category | Marine GPS System |
| Language | English |
Caution regarding microwave power radiation during transmission.
Precautions for handling ESD sensitive components.
Model, FCC ID, and RF exposure compliance details.
Important notices regarding device operation and modifications.
Definitions of acronyms and technical terms used in the manual.
Overview of the manual's content, scope, and intended use.
Lists relevant and cited documents for the AVIATOR UAV 200.
Defines the manual's scope and provides a system overview of the SATCOM terminal.
Describes the main connector (J1) and its associated mating connectors.
Diagram illustrating the pin configuration of the J1 connector.
Detailed table of pin functions, names, and wire gauges.
Overview of installation, storage, unpacking, and USIM card insertion.
Guidance on terminal weight, heat dissipation, and optimal placement.
Considerations for system placement, mounting, and environmental sealing.
Instructions for connecting Ethernet and RS-232 interfaces.
Specifies power source voltage, wattage, and wire gauge for the terminal.
Procedure for grounding the unit to the airframe via designated surfaces.
Identifies terminal surfaces for grounding and bonding.
Factors affecting terminal alignment and mounting constraints.
Diagrams showing terminal orientation, sides, and reference axes.
Steps to measure and program installation offset angles for satellite tracking.
Notes on lightning protection and specifications for mounting screws.
Steps to disconnect and remove the terminal from its installation.
Terminal requires no routine maintenance; return for repair.
How to generate, download, and use event logs for troubleshooting.
Lists specific tools like milliohm meter and torque driver for installation.
Power, dimensions, weight, temperature range, and frequency specifications.
Summary of environmental test conditions and categories the terminal meets.
Initial setup requirements including USIM and navigational input.
Minimum parameters to set via the web interface dashboard.
Configuring RS-232 ports for AT command or transparent data modes.
Configuring proxy, APN, username, and password for transparent mode.
Adjusting router mode, IP address, and DHCP server settings.
Inputting measured offset angles for antenna steering.
Using AT commands for navigation data and terminal control.
Overview of the dashboard and steps to connect to the web interface.
Explains status bar icons and the overall menu hierarchy.
Diagram of the Control Panel's main sections and sub-functions.
Navigating to advanced settings after administrator login.
Steps to access and modify connection settings.
Viewing details of a connection package.
Renaming an existing connection package.
Accessing the connection filter details.
Configuring APN, username, and password for a connection.
Navigating the main sections of the Control Panel.
Choosing between Transparent or AT Command mode for RS-232 ports.
Setting operational mode, baud rate, and other parameters for RS-232 ports.
Detailed configuration for transparent mode operation.
Adjusting router mode, IP, DHCP, and installation angles.
Restricting data traffic types for connected devices.
Accessing advanced features via administrator login.
Overview of menu options available in the advanced panel.
Accessing and managing system, connection, and navigation event logs.
Creating flight logs and viewing historical data logs.
Summary of data usage totals for different service types.
Setting up rules to translate addresses and ports for network traffic.
Setting server, APN, and report intervals for position tracking.
Accessing alerts, status, software updates, and reboot functions.
Viewing alerts, terminal status, and resetting passwords.
Creating and downloading diagnostic reports for troubleshooting.
Displays system, connection, and navigation related events.
Instructions for updating the terminal's software.
Steps to reboot the terminal and confirmation prompt.
Displays software and hardware version details for support.
Navigating to the advanced control panel after administrator login.
Managing user access rights for terminal functions.
Backing up and restoring terminal settings.
Enabling or disabling remote control of the tracking function.
Monitoring terminal connectivity using PING at intervals.
Configuring estimated call costs for different service types.
Reverting terminal software to default factory settings.
Changing administrator and user passwords.
Managing data flow for connections using templates.
Configuring filters for UDP and TCP traffic.
Defining custom rules for filtering network traffic.
Monitoring terminal connectivity using PING at intervals.
Configuring data usage limits for different service types.
Programming the supplier's email address for support.
How to get assistance for purchased systems.
Procedure for obtaining Return Material Authorization for repairs.
Details on returns, policies, and repackaging requirements.
Recommendations for correct disposal of the product.
To Next Page
