Circuit Breaker : ON
Unit Switch : ON
USDA:
OFF or AU (or 3 , 4)
dHU: OFF (or ON)
S
Press for
3 seconds
Press for
3 seconds
Press for
3 seconds
DECOS
3
: d ( or C,B,A)
Log. Int :60 or 30 (or 120,15)
REC SEN: ON (or OFF)
OC-SET : Sing (or dUAL)
HP : 10 (or 5)
DISP: OFF (or ON )
COMP:100 (or 33)
REHEAT: ON or OFF
FA SEN: OFF or L (or H)
S
S
S
S
S
S
S
S
H001 : 3 H005 : 3
H002 : 2 H006 : 1
H003 : 2 d : 1
H004 : 2 d2 : 1
S
S
S
S
S
S
S
S
S
SS
※10.
Optional Function Setting Mode
※11.
Basic Function Setting Mode
S
S
S
S
Key Operation
OPERATION
DECOSⅢd only
(FA SEN)
White label
DECOSⅢc
for LXE10E-A
:
: Manual action
:
Select key
:
S key
:
Enter key
:
Controller operation
DECOSⅢd & Ⅲc only
(REHEAT)
DECOSⅢb
for LXE10D
Connector
CN20 to VOD
(FA sensor)
Blue label
DECOS Ⅲd
for LXE10E-1
--
& LXE10E-A
S
d-1 : 1
d-2 : 1
d3 : 1
1.Underlined figures show the value of the most usual setting case. Actually all the settings have been set to DECOS3d, 3c, and 3b INITIAL SETTING
TABLE at factory. If there is not specify special instruction, set all figures to "Factory set".
2.When the setting change is required, select the desired setting using or key and press key to confirm, and then turn circuit breaker off.
3.When controller is replaced from the spare parts, confirm the model name first, and then set a items by following INITIAL SETTING TABLES
△
▽
INITIAL
SETTING
for
4 MODES
TRIP START
SETTING
OPERATION
CONDITION
SETTING
Unit Switch : OFF
Unit Switch : ON
※13. Input Data Mode
SET I.d (Container I.D)
i.d.-C
Set 4 alphabets
i.d-n
Set 7 numbers (numeral)
SET I.d
SET TIME
Set year, month & day
Set hour and minute
Press for 3 seconds
in 18 seconds
※6. PTI selection mode (for Trip Start Setting)
1. Select ｢Manual Check｣ with △ or ▽ key and
determine it with Enter key.
2. Select Trip Start ｢TS H｣ with △ or ▽ key and
set it to "0" by pressing Enter key for 3 seconds.
All Indication light ON (for 3 seconds)
Starting preparation (for 18 seconds)
All Indication light ON (for 3 seconds)
Starting preparation (for 18 seconds)
All Indication light ON (for 3 seconds)
Starting preparation (for 18 seconds)
Alarm F301 : Non setting of [Control Temperature]
E303 : Non setting of [Control Humidity]
if dHU is set to ON
E305 : Non setting of [Defrost Interval]
Operation
Unit Switch
OFF
Unit Switch
ON
※2. Operation setting mode
Set Control Temperature
Set Control Humidity
if dHU is set to ON.
Set Defrost Interval.
Circuit
Breaker
OFF
Circuit
Breaker
ON
※12. Optional Condition Setting Mode
CHARTLS : OFF or ON
USDA 1/2 : 1or 2
To Next Page
Loading...
