Danby DPAC10071 - Window;Patio Door Kit Installation; Rain Hood Assembly

Rain
Hood
Assembly
1)
Fold both
sides of
the
Rain
Hood
9Q0
as so
the
flanges are
facing
outward. Fig
1
of
Window
I Patio Door
Kit Installation
(Air Conditioning
Mode
ONLY)
Your
window kit
has
been
designed
to fit most
standard
“vertical”
I
“horizontal”
windows
and
patio
doors
up
to a
maximum
height
of
80”.
For
vertical
window
and/or patio
door
applications,
lock
positions
are
provided
on
the
fornt
of
each slidersection.
Wing
nuts
are
provided
(ontheslidersection)
to secure the
section
together.
Fig.
5a.
Horizontal
Window
44
\
Window
Slider Kit
Minimum:
28”
(71.1 cm)
Maximum:
48 /8”
(123
cm)
Fig. 3a
Rain hood
inserts are
installed in “A”
and “B”
postions with
vent
opening
facing down
(C)
2)
Slide
the Rain
Hood
flanges
the
edges
the
slider
kit until it
is
lined up
with the intake
_______________________
vent
(shown
in Fig 2).
Once the mounting
holes
on
the
slider, as
well
as
the
Rain
Hood
are
aligned,
secure
the Rain
Hood to
the
slider with
the four
mounting
screws
provided.
Fig. I
4
Vertical
Wind
t
Jii
Li
Rain Hood
is to be
installed
only over
air
intake
vent
\
Slider
kit
Fig.
2
adapter
Window
Slider
Kit
Minimum:
28’
(71.1 cm)
Maximum: 48
/8” (123 cm)
Rain hood
inserts are
installed
in “A”
and
“C”
positions
with
vent
opening
facing
down
(B)
Fig.4a
L
IMPORTANT:
• For
horizontal
window
kit applications
refer
to
figure
3a for
correct Rain
Hood
insert positioning.
• For vertical
window
kit
applications
(including
patio)
refer to
figure 4a
for correct
Rain Hood
insert
positioning.
1)
Select
a suitable
Iocation,making
sure
you
have
access
to
an
electrical
outlet.
2)
Install
both flexible
hoses
to the rear
side of the
unit. Both
hoses
are
identical
and
can be
installed
into
either
opening.
Insert
the hose
collar with
the 2
lock tabs
into the 2
slots on the
top of each
opening
and twist
to lock into
position.
3)
Install
the adjustable
Window/Patio
Door Slider
Kit as required.
Fig’s.
3, 4, 5.
4) Install
the
window
exhaust
adapters
into the
openings
in the
slider section,
making
sure
the
window
slider sections
are
secure.
Important::
Ensure
the
exhaust
adapter
labeled
“air
intake”
is installed
on the
hose that is
connected
to
the
air
intake
opening
on
the back
of the unit.
Please
Note: In
a
vertical
application,
the
exhaust
hose MUST
be
positioned
above
the
intake
hose in the
window
slider.
See
Fig
5.
This will
avoid having
the exhaust
heat
go
through
the
intake
and back
into
the unit.
Patio
Door
Fig. 5
Patio Door
Kit
Minimum:
28”
(67.5
cm)
Maximum:
80” (203
cm)
Plug
the unit
into
a
115 V
I 60
Hz grounded
7
electrical
outlet.