Danfoss FC 100 Series - Navigating the Main Menu Mode

Q3-4 Application Settings
Q3-40 Fan Functions Q3-41 Pump Functions Q3-42 Compressor Functions
Par. 22-60 Broken Belt Function Par. 22-20 Low Power Auto Set-up Par. 1-03 Torque Characteristics
Par. 22-61 Broken Belt Torque Par. 22-21 Low Power Detection Par. 1-71 Start Delay
Par. 22-62 Broken Belt Delay Par. 22-22 Low Speed Detection Par. 22-75 Short Cycle Protection
Par. 4-64 Semi-Auto Bypass Set-up Par. 22-23 No-Flow Function Par. 22-76 Interval between Starts
Par. 1-03 Torque Characteristics Par. 22-24 No-Flow Delay Par. 22-77 Minimum Run Time
Par. 22-22 Low Speed Detection Par. 22-40 Minimum Run Time Par. 5-01 Terminal 27 Mode
Par. 22-23 No-Flow Function Par. 22-41 Minimum Sleep Time Par. 5-02 Terminal 29 Mode
Par. 22-24 No-Flow Delay Par. 22-42 Wake-up Speed [RPM] Par. 5-12 Terminal 27 Digital Input
Par. 22-40 Minimum Run Time Par. 22-43 Wake-up Speed [Hz] Par. 5-13 Terminal 29 Digital Input
Par. 22-41 Minimum Sleep Time Par. 22-44 Wake-up Ref./FB Difference Par. 5-40 Function Relay
Par. 22-42 Wake-up Speed [RPM] Par. 22-45 Setpoint Boost Par. 1-73 Flying Start
Par. 22-43 Wake-up Speed [Hz] Par. 22-46 Maximum Boost Time Par. 1-86 Trip Speed Low [RPM]
Par. 22-44 Wake-up Ref./FB Difference Par. 22-26 Dry Pump Function Par. 1-87 Trip Speed Low [Hz]
Par. 22-45 Setpoint Boost Par. 22-27 Dry Pump Delay
Par. 22-46 Maximum Boost Time Par. 22-80 Flow Compensation
Par. 2-10 Brake Function Par. 22-81 Square-linear Curve Approximation
Par. 2-16 AC brake Max. Current Par. 22-82 Work Point Calculation
Par. 2-17 Over-voltage Control Par. 22-83 Spe
ed at No-Flow [RPM]
Par. 1-73 Flying Start Par. 22-84 Speed at No-Flow [Hz]
Par. 1-71 Start Delay Par. 22-85 Speed at Design Point [RPM]
Par. 1-80 Function at Stop Par. 22-86 Speed at Design Point [Hz]
Par. 2-00 DC Hold/Preheat Current Par. 22-87 Pressure at No-Flow Speed
Par. 4-10 Motor Speed Direction Par. 22-88 Pressure at Rated Speed
Par. 22-89 Flow at Design Point
Par. 22-90 Flow at Rated Speed
Par. 1-03 Torque Characteristics
Par. 1-73 Flying Start
See also VLT HVAC Drive Programming Guide for a detailed
description of the Function Setups parameter groups.
7.1.2 Main Menu Mode
Both the GLCP and NLCP provide access to the main menu
mode. Select the Main Menu mode by pressing the [Main
Menu] key. Illustration 6.2 shows the resulting read-out, which
appears on the display of the GLCP.
Lines 2 through 5 on the display show a list of parameter
groups which can be chosen by toggling the up and down
buttons.
Illustration 7.8: Display example.
Each parameter has a name and number which remain the
same regardless of the programming mode. In the Main Menu
mode, the parameters are divided into groups. The first digit
of the parameter number (from the left) indicates the parame-
ter group number.
All parameters can be changed in the Main Menu. The config-
uration of the unit (par. 1-00 Configuration Mode) will
determine other parameters available for programming. For
example, selecting Closed Loop enables additional parameters
related to closed loop operation. Option cards added to the
unit enable additional parameters associated with the option
device.
How to Programme the Frequ...
VLT
®
HVAC Drive Operating Instructions
MG.11.AD.02 - VLT
®
is a registered Danfoss trademark 63
7
7