Danfoss VLT Micro Drive Programming Guide

5.1.13 8-** Comm. and Options
Parameter
Number
Parameter Description Default Value 2 Setup
Change During
Operation
Conversi
on Index
Type
8-01 Control Site [0] Digital and ctrl.word All set-ups TRUE - Uint8
8-02 Control Word Source [1] FC RS485 All set-ups TRUE - Uint8
8-03 Control Word Timeout Time 1 s 1 set-up TRUE -1 Uint16
8-04 Control Word Timeout Function [0] Off 1 set-up TRUE - Uint8
8-06 Reset Control Word Timeout [0] No function 1 set-up TRUE - Uint8
8-30 Protocol [0] FC 1 set-up TRUE 0 Uint8
8-31 Address 1 1 set-up TRUE 0 Uint8
8-32 FC Port Baud Rate [2] 9600 Baud 1 set-up TRUE - Uint8
8-33 FC Port Parity [0] Even Parity 1 Stop Bit 1 set-up TRUE - Uint8
8-35 Minimum Response Delay 0.01 s 1 set-up TRUE -3 Uint16
8-36 Max Response Delay 5 s 1 set-up TRUE -3 Uint16
8-43 FC Port PCD Read Configuration 0 1 set-up TRUE - Uint8
8-50 Coasting Select [3] Logic OR All set-ups TRUE - Uint8
8-51 Quick Stop Select [3] Logic OR All set-ups TRUE - Uint8
8-52 DC Brake Select [3] Logic OR All set-ups TRUE - Uint8
8-53 Start Select [3] Logic OR All set-ups TRUE - Uint8
8-54 Reversing Select [3] Logic OR All set-ups TRUE - Uint8
8-55 Set-up Select [3] Logic OR All set-ups TRUE - Uint8
8-56 Preset Reference Select [3] Logic OR All set-ups TRUE - Uint8
8-94 Bus feedback 1 0 All set-ups TRUE 0 Int16
Table 5.16
5.1.14
13-** Smart Logic
Parameter
Number
Parameter Description Default Value 2 Setup
Change During
Operation
Conversi
on Index
Type
13-00 SL Controller Mode [0] Off 1 set-up TRUE - Uint8
13-01 Start Event [39] Start command 1 set-up TRUE - Uint8
13-02 Stop Event [40] Drive stopped 1 set-up TRUE - Uint8
13-03 Reset SLC [0] Do not reset 1 set-up TRUE - Uint8
13-10 Comparator Operand [0] Disabled 1 set-up TRUE - Uint8
13-11 Comparator Operator [1] ApproxEqual 1 set-up TRUE - Uint8
13-12 Comparator Value 0 1 set-up TRUE -1 Int32
13-20 SL Controller Timer 0 s 1 set-up TRUE -1 Uint32
13-40 Logic Rule Boolean 1 [0] False 1 set-up TRUE - Uint8
13-41 Logic Rule Operator 1 [0] Disabled 1 set-up TRUE - Uint8
13-42 Logic Rule Boolean 2 [0] False 1 set-up TRUE - Uint8
13-43 Logic Rule Operator 2 [0] Disabled 1 set-up TRUE - Uint8
13-44 Logic Rule Boolean 3 [0] False 1 set-up TRUE - Uint8
13-51 SL Controller Event [0] False 1 set-up TRUE - Uint8
13-52 SL Controller Action [0] Disabled 1 set-up TRUE - Uint8
Table 5.17
Parameter Lists
VLT
®
Micro Drive FC 51 Programming Guide
60 MG02C602 - VLT
®
is a registered Danfoss trademark
55

Danfoss VLT Micro Drive Specifications

General

Brand	Danfoss
Model	VLT Micro Drive
Category	DC Drives
Language	English