Danfoss VLT Midi Drive FC 280 - Page 125

7-60 Feedback 1 Conversion [0] Linear All set-ups TRUE - Uint8
7-62 Feedback 2 Conversion [0] Linear All set-ups TRUE - Uint8
5.2.9 8-** Communications and Options
Param
eter #
Parameter description Default value 4 set-up Change during
operation
Conversion
index
Type
8-0* General Settings
8-01 Control Site
[0] Digital and
ctrl.word All set-ups TRUE - Uint8
8-02 Control Source ExpressionLimit All set-ups TRUE - Uint8
8-03 Control Timeout Time 1 s 1 set-up TRUE -1 Uint16
8-04 Control Timeout Function [0] O 1 set-up TRUE - Uint8
8-07 Diagnosis Trigger [0] Disable 1 set-up TRUE - Uint8
8-1* Ctrl. Word Settings
8-10 Control Word Prole [0] FC prole All set-ups TRUE - Uint8
8-14 Congurable Control Word CTW [1] Prole default All set-ups TRUE - Uint8
8-19 Product Code ExpressionLimit 1 set-up TRUE 0 Uint32
8-3* FC Port Settings
8-30 Protocol [0] FC 1 set-up TRUE - Uint8
8-31 Address 1 N/A 1 set-up TRUE 0 Uint8
8-32 Baud Rate ExpressionLimit 1 set-up TRUE - Uint8
8-33 Parity / Stop Bits ExpressionLimit 1 set-up TRUE - Uint8
8-35 Minimum Response Delay 0.01 s 1 set-up TRUE -3 Uint16
8-36 Maximum Response Delay ExpressionLimit 1 set-up TRUE -3 Uint16
8-37 Maximum Inter-char delay 0.025 s 1 set-up TRUE -3 Uint16
8-4* FC MC protocol set
8-42 PCD Write Conguration ExpressionLimit 2 set-ups TRUE - Uint8
8-43 PCD Read Conguration ExpressionLimit 1 set-up TRUE - uint8
8-5* Digital/Bus
8-50 Coasting Select [3] Logic OR All set-ups TRUE - Uint8
8-51 Quick Stop Select [3] Logic OR All set-ups TRUE - Uint8
8-52 DC Brake Select [3] Logic OR All set-ups TRUE - Uint8
8-53 Start Select [3] Logic OR All set-ups TRUE - Uint8
8-54 Reversing Select [3] Logic OR All set-ups TRUE - Uint8
8-55 Set-up Select [3] Logic OR All set-ups TRUE - Uint8
8-56 Preset Reference Select [3] Logic OR All set-ups TRUE - Uint8
8-57 Prodrive OFF2 Select [3] Logic OR All set-ups TRUE - Uint8
8-58 Prodrive OFF3 Select [3] Logic OR All set-ups TRUE - Uint8
8-7* BACnet
8-79 Protocol Firmware version ExpressionLimit 1 set-up FALSE -2 Uint16
8-8* FC Port Diagnostics
8-80 Bus Message Count 0 N/A 1 set-up TRUE 0 Uint32
8-81 Bus Error Count 0 N/A 1 set-up TRUE 0 Uint32
8-82 Slave Messages Rcvd 0 N/A 1 set-up TRUE 0 Uint32
8-83 Slave Error Count 0 N/A 1 set-up TRUE 0 Uint32
8-84 Slave Messages Sent 0 N/A 1 set-up TRUE 0 Uint32
8-85 Slave Timeout Errors 0 N/A 1 set-up TRUE 0 Uint32
8-88 Reset FC port Diagnostics [0] Do not reset 1 set-up TRUE - Uint8
8-9* Bus Feedback
8-90 Bus Jog 1 Speed 100 RPM All set-ups TRUE 67 Uint16
8-91 Bus Jog 2 Speed 200 RPM All set-ups TRUE 67 Uint16
Parameter Lists Programming Guide
MG07C102 Danfoss A/S © 12/2015 All rights reserved. 123
5 5