DSE Model 8620 AMF Controller Operators Manual
4
4.1
TERMINAL DESCRIPTION ........................................................................................ 36
4.1.1
DC SUPPLY, FUEL AND START OUTPUTS, OUTPUTS E-J .................................. 37
4.1.2
ANALOGUE SENSOR ......................................................................................... 38
4.1.3
MAGNETIC PICKUP, CAN AND EXPANSION ....................................................... 39
4.1.4
V1 LOAD SWITCHING AND GENERATOR VOLTAGE SENSING .......................... 40
4.1.5
V2 MAINS VOLTAGE SENSING ......................................................................... 40
4.1.6
GENERATOR CURRENT TRANSFORMERS ........................................................ 41
4.1.7
MAINS CURRENT TRANSFORMERS .................................................................. 41
4.1.8
CONFIGURABLE DIGITAL INPUTS ..................................................................... 43
4.1.9
PC CONFIGURATION INTERFACE CONNECTOR................................................ 43
4.1.10
RS485 CONNECTOR .......................................................................................... 44
4.1.11
RS232 CONNECTOR .......................................................................................... 44
4.2
TYPICAL WIRING DIAGRAMS ................................................................................... 45
4.2.1
3 PHASE, 4 WIRE WITH RESTRICTED EARTH FAULT PROTECTION .................. 46
4.3
ALTERNATIVE TOPOLOGIES .................................................................................. 47
4.3.1
3 PHASE, 4 WIRE WITHOUT EARTH FAULT PROTECTION ................................. 47
4.3.2
SINGLE PHASE WITH RESTRICTED EARTH FAULT............................................ 48
4.3.3
SINGLE PHASE WITHOUT EARTH FAULT........................................................... 48
4.3.4
2 PHASE (L1 & L2) 3 WIRE WITH RESTRICTED EARTH FAULT .......................... 49
4.3.5
2 PHASE (L1 & L2) 3 WIRE WITHOUT EARTH FAULT ......................................... 49
4.3.6
2 PHASE (L1 & L3) 3 WIRE WITH RESTRICTED EARTH FAULT .......................... 50
4.3.7
2 PHASE (L1 & L3) 3 WIRE WITHOUT EARTH FAULT MEASURING ..................... 50
4.3.8
3 PHASE 4 WIRE WITH UNRESTRICTED EARTH FAULT MEASURING ................ 51
4.3.9
EARTH SYSTEMS .............................................................................................. 51
4.4
TYPICAL ARRANGEMENT OF DSENET® ................................................................. 52
4.4.1
EARTH SYSTEMS .............................................................................................. 53
5
DESCRIPTION OF CONTROLS .................................................................. 54
5.1
DSE8620 AUTOMATIC MAINS FAILURE (AMF) CONTROL MODULE ........................ 54
5.2
VIEWING THE INSTRUMENT PAGES ....................................................................... 56
5.2.1
STATUS ............................................................................................................. 57
5.2.2
ENGINE ............................................................................................................. 58
5.2.3
GENERATOR ..................................................................................................... 59
5.2.4
MAINS ............................................................................................................... 59
5.2.1
RS232 SERIAL PORT ......................................................................................... 60
5.2.1
RS485 SERIAL PORT ......................................................................................... 63
5.2.2
ABOUT .............................................................................................................. 64
5.2.1
CAN ERROR MESSAGES................................................................................... 66
5.3
VIEWING THE EVENT LOG ...................................................................................... 67
5.4
USER CONFIGURABLE INDICATORS ....................................................................... 68
6
OPERATION ............................................................................................... 69
6.1
CONTROL ................................................................................................................ 69
6.2
CONTROL PUSH-BUTTONS .................................................................................... 70
6.3
DUMMY LOAD / LOAD SHEDDING CONTROL .......................................................... 72
6.4
STOP MODE ............................................................................................................ 73
6.4.1
ECU OVERRIDE ................................................................................................. 74
6.5
AUTOMATIC OPERATION ........................................................................................ 75
6.5.1
MAINS FAILURE................................................................................................. 75
6.5.1
ENGINE RUNNING.............................................................................................. 76
6.5.2
REMOTE START IN ISLAND MODE .................................................................... 77
6.5.3
REMOTE START ON LOAD ................................................................................ 79
6.6
MANUAL OPERATION .............................................................................................. 81
6.7
TEST OPERATION ................................................................................................... 83
7
PROTECTIONS ........................................................................................... 85
7.1
PROTECTIONS DISABLED ....................................................................................... 86
7.1.1
INDICATION / WARNING ALARMS...................................................................... 86
To Next Page
Loading...
Need help?
General
