Denon AVR-1000 - Speaker Volume, Pro Logic, and DSP Adjustments

16
© Speaker volume adjustment and Dolby Pro Logic mode
To
obtain
the
maximum
surround
effect,
use
the
test
tones
to
adjust
the
volume
and
balance
of
the
speakers
for
the
best
balance
for
the
listening
position
and
so
that
the
sound
from
ail
the
speakers
is
heard
at
the
same
ievel.
Auto mode Manual mode
1. Press the T.TONE button.
T.TONE
Cey
Remote control unit
6. Switch to the manual mode.
PARAMETER:
Remote control unit
Auto mode +— manual mode
The mode switches as shown above.
Test tones are produced from the speak-
ers in the order shown below, at 4 second
intervals for the first two cycies, 2 second
intervals after that. .
For the Dolby 3CH Lagic mode:
pre eg Dacre ae
. To increase the levei of the center
speaker:
- To emit the test tones in the clockwise
direction.
WWNHhW WH
SY
Remote contro! unit
mats —+>[¢]— [FR] SI >
. To emit the test tones in the counterclock-
wise direction.
a
Co<y
CENTER
Remote contro} unit
Remote control unit
pl) — (Ce) — fF -— FS
. To decrease the level of the center
speaker:
CENTER
Cy
Remote contro! unit
. Follow steps 2 to 5 for the auto mode to
adjust the level of the different speakers.
. To increase the tevel of the rear speakers:
Remote control unit
Cancelling
10.Press the T.TONE button again.
T TONE
. To decrease the level of the rear
speakers:
Cay
Remote control unit
Remote control unit
NOTES:
e@ When the T.TONE button is pressed, the auto mode is set |
The ‘evel of the center and rear channels can be adjusted
and test tones are produced starting from the front left from OdB to -24dB in steps of 2dB.
channel.
@ Inthe auto mode, the test tone will not move on to the next
channel when it is being emitted from the center channe}
and the jevel of the center speakers is being adjusted, or
when it is being emitted from the rear channel and the level
of the rear speakers is being adjusted. It only moves on to
the next channel approximately two seconds after the level
key has been released.
«@ When the mode is switched from the auto mode to the
manual mode, the test tone is emitted starting from the
channel from which it was last being emitted in the auto
mode.
Once the levet of the center and rear channe!s is set, there
is no need to readjust it unless you change the speaker
system or the listening room. However, when the CLEAR
@ button is pressed, the mode changes as shown on the
table on Page 18. In this case, reset the center mode.
In other surround modes, adjust the balance based on the
adjustment made in the Dolby Pro Logic made. The
balance may not be optimum for some sources, so readjust
it as necessary.
@ Other DSP Surround Modes
e Using the directivity emphasis circuit and DSP surround
Use this to play sources recorded in Dolby Stereo and Dolby Surround with even greater power.
(The
directivity
emphasis
circuit
detects
the
signals
with
the
dominant
direction
from
the
level
and
phase
of
the
left
and
right
channels
and produces a sharp acoustic image and sense of direction.)
Wide
1. When playing movies. cot the
Screen mode.
When playing music, set the Live mode.
SURR. MOOE
Main unit Remote controi unit
> Wie SCREEN — PRO LOGIC — sTaoum
2. Set the center mode.
Set to the center mode set in the Dolby
Pro Logic mode.
3. Start playing the movie or music.
4. Adjust the volume.
(ox
Main unit 1
Adjusting the effect levet
8. Select the effect level mode.
: Os
Remote control unit
DELAY -—+ EFFECT LEVEL
The parameter switches as shown above.
Remote contro! unit
5. Adjust the level of the center and rear
channels.
Adjust the levels according to the source,
using the Dolby Pro Logic settings as
reference.
9. To increase the effect level.
Coy
Remote contrat unit
Adjusting the detay time
6. Select the delay time mode.
PARAMETER
10.To decrease the effect level.
Rig,
Remote contro! unit
Remote control unit
DELAY +—~ EFFECT LEVEL
The parameter switches as shown above.
7. Set the delay time following the proce-
dure on Page 15.
e@ DSP surround playback
Other adjustments
11.Follow steps 6 to 8 under “Playing the
program source”. on Page 11.
1. Select the desired surround mode.
mone
Main unit
4 mone MOVIE
> cc saa
> Rock
= STADIUM
3. Play the desired software.
4. Adjust the volume.
ron
| Remote controt unit
LIVE
t
WIDE SCAFEN
PRO LOGIC
8. Adjust the effect level.
Adjust the level in the same way as for
the Wide Screen mode above.
11.Foltow steps 6 to 8 under “Playing the
program source” on Page 11.
To turn off the surround mode
12.Press the BYPASS button.
Cy
Main unit
Normat stereo playback resumes.
MASTER VOLUME
aes
Remate contro! unit
Main unit | BYPASS
a
| CS
Remote control unit
5. Adjust the level of the rear channel.
Adjust the level according to the source,
using the Dolby Pro Logic settings as
reference.