C
Courtney WongSep 9, 2025
Why Dynamic EQ and Dynamic Volume cannot be selected on Denon AVR-2312 Receiver?
- SSarah WoodSep 9, 2025
If you can't select Dynamic EQ® and Dynamic Volume® on your Denon Receiver, run Audyssey® Auto Setup.
To Next PageTo Next PageWhy Dynamic EQ and Dynamic Volume cannot be selected on Denon AVR-2312 Receiver?
If you can't select Dynamic EQ® and Dynamic Volume® on your Denon Receiver, run Audyssey® Auto Setup.
Why Audyssey MultEQ, Dynamic EQ and Dynamic Volume cannot be selected on Denon AVR-2312 Receiver?
If you cannot select Audyssey MultEQ® XT, Audyssey Dynamic EQ®, and Audyssey Dynamic Volume® on your Denon Receiver, switch the surround mode to something other than “DIRECT” or “PURE DIRECT”. Also, these features are unavailable when headphones are in use.
Why Dolby PLg mode or DTS NEO:6 mode cannot be selected on Denon AVR-2312?
If Dolby PLg or DTS NEO:6 mode cannot be selected on your Denon Receiver, check that “Speaker Config.” – “Center” or “Surround” is set to something other than “None”. This surround mode is unavailable for 2.0/2.1ch speaker systems, and when headphones are in use.
Why RESTORER cannot be selected on Denon AVR-2312 Receiver?
If RESTORER cannot be selected on your Denon Receiver, ensure that an analog signal or PCM signal (fs=44.1/48 kHz) is input. RESTORER is not usable for multichannel signals like Dolby Digital or DTS surround. Also, switch the surround mode to something other than “DIRECT” or “PURE DIRECT”.
General| Impedance | 8 Ω |
|---|---|
| Speaker selector | A+B |
| Input sensitivity | 200 mV |
| Pre-out connectivity | Yes |
| Audio output channels | 7.1 channels |
| Audio A/D Converter (ADC) | 24-bit/96kHz |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Total Harmonic Distortion (THD) | 0.08 % |
| Power output per channel (1KHz@8 Ohm) | 135 W |
| Power output per channel (20-20KHz@8 Ohm) | 105 W |
| HDMI in | 7 |
| Composite video in | 4 |
| Ethernet LAN (RJ-45) ports | 1 |
| Multichannel audio input type | RCA |
| Component video (YPbPr/YCbCr) in | 2 |
| Headphone connectivity | 6.3 mm |
| Connectivity technology | Wired |
| Speakers connectivity type | Binding post |
| Audio formats supported | AAC, FLAC, MP3, WAV, WMA |
| Image formats supported | JPG |
| Wi-Fi | No |
| AM band range | 522 - 1611 kHz |
| FM band range | 87.5 - 108 MHz |
| Supported radio bands | AM, FM |
| Preset stations quantity | 56 |
| Internet radio services supported | Last.fm, Napster |
| Supported video modes | 1080i, 1080p, 480i, 480p, 576i, 576p, 720p |
| Display | VFD |
| HDMI version | 1.4a |
| Product color | Black |
| Audio decoders | Dolby Pro Logic IIz, Dolby TrueHD, DTS-HD Master Audio |
| Volume control | Rotary |
| Apple docking compatibility | iPad, iPhone, iPod |
| Number of products included | 1 pc(s) |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Power consumption (standby) | 0.1 W |
| Power consumption (typical) | 600 W |
Weight and Dimensions| Depth | 382 mm |
|---|---|
| Width | 434 mm |
| Height | 167 mm |
| Weight | 11000 g |
Procedure for checking leakage current before returning the set to the customer.
General cautions and instructions for servicing and inspection.
Explains how to set special modes using buttons.
Lists strategies to resolve identified error codes.
Details what is displayed on the FL display for different protection incidents.
Indicates warnings shown by the POWER LED based on protection incident conditions.
Steps to set up AV receivers for Remote ID.
Steps to set the remote control unit for Remote ID.
Instructions on how to start the diagnostic mode.
Instructions on how to cancel the diagnostic mode.
Lists video system confirmation items and their details.
Steps to check for and update the firmware.
Lists error codes related to firmware updates.
Provides details of each error code.
Lists strategies to resolve identified error codes.
Procedure for adjusting idling current for the audio section.
Detailed steps for performing the adjustment.
Shows available surround modes and adjustable parameters.
Troubleshooting steps for power-related issues.
Flowchart for diagnosing power-on issues.
Troubleshooting steps when a fuse is blown.
Troubleshooting flowchart for no picture or sound issues over HDMI.
Diagnoses issues when the set does not recognize the TV.
Troubleshooting flowchart for audio output issues.
Troubleshooting steps for network connectivity issues.
Verifies network settings on the receiver and peripherals.
Steps to check the USB device and its compatibility.
Checks the AV receiver's USB connection and power.
Checks video signals for no picture output.
Checks S/PDIF signals for no sound output.
Checks for damage in IC901.
Checks if the fuse is blown.
Pin descriptions and functions for IC201 (R5F5630ECDFB).
Lists pin names, I/O, and functions for LC89058W-E.
Lists pin names, I/O, and functions for ADSP21487KSWZ.
Block diagram for the W9864G6JH-6 memory chip.
Block diagram for the MX29LV160DBTI-70G flash memory.
Block diagram for the AK4424ET DAC converter.
Lists pin names, I/O, and functions for AK5358BET ADC.
Lists pin names, I/O, and functions for AK4358VQ DAC.
Lists pin names and functions for H27U1G8F2BTR-BC NAND Flash.
Block diagram for the H27U1G8F2BTR-BC NAND Flash.
Block diagram for the W9825G6JH-6 SDRAM.
Lists pin names and functions for W9825G6JH-6 SDRAM.
Block diagram for the LAN8700 Ethernet PHY.
Block diagram for the SAA7121 Video Encoder.
Lists pin names and functions for R2A15220FP audio IC.
Block diagram for the NJW1194A audio IC.
