Denon AVR-4311 User Manual

63
Basic versionSimple version Information
ENGLISH
Advanced version
Convenient functions
Quick select function
All of the settings in step 1 can be memorized together. By memorizing
frequently used settings, you can quickly access and enjoy a playback
environment that is consistently the same.
n Saving the settings
1
Set the items below to the settings you want to save.
q Input source (vpage28)
w Volume (vpage28)
e Surround Mode (vpage46)
r Video Select (vpage78)
t Audyssey Setting
(MultEQ
®
XT 32, Dynamic EQ
®
,
Dynamic Volume
®
) (vpage85)
2
Press and hold the desired QUICK SELECT until
“Memory” appears on the display.
The current settings will be memorized.
GQuick select defaultsH
Input source Volume
QUICK SELECT 1 BD –40 dB
QUICK SELECT 2 SAT/CBL –40 dB
QUICK SELECT 3 DOCK –40 dB
n Recalling the settings
Press QUICK SELECT at which the
settings you want to call out are saved.
The , or indicator illuminates on
the display.
Naming quick select settings
See “Quick Select Name” (vpage101).
• The Quick Select function can be set separately for the different
zones (vpage70 “Quick select function”).
• If
QUICK SELECT on the main unit
is pressed, the same function as
with the remote control unit can be
obtained.
NOTE
Input sources stored with the quick select function cannot be selected
if they have been deleted at “Source Delete” (vpage100). In this case,
store them again.
REC OUT mode
When using the audio/video recording connectors (DVR outputs), you
can record the audio or video from a different program source while
listening to the currently played track.
1
Press ZONE2/3 / REC SELECT.
“ZONE2 SOURCE” is shown on the
display.
2
Turn SOURCE SELECT until
“RECOUT SOURCE” is
displayed.
The indicator illuminates.
ZONE2 SOURCE ZONE2 TUNER ZONE2 NET/USB
····
RECOUT NET/USB RECOUT DOCK RECOUT SOURCE
····
3
Turn SOURCE SELECT to choose the input source to
be recorded.
• For operating instructions, refer to the respective equipment’s
operating instructions.
4
Start recording.
• For operating instructions, refer to the respective equipment’s
operating instructions.
• To cancel, press ZONE2/3 / REC SELECT, then turn SOURCE SELECT
until “ZONE2 SOURCE” is displayed.
• Make a test recording before starting the actual recording.
• Signals are only output to the analog REC OUT connectors when
the digital signals input to the digital input connectors (OPTICAL/
COAXIAL) are PCM (2-channel) signals.
• As the digital audio signal input from the HDMI or DENON LINK
connector is not output to the digital recording connector (OPTICAL),
you should connect using the OPTICAL and COAXIAL connectors.
• Sources selected with the REC OUT mode are output from ZONE2
as well.
• The operable buttons on the remote control unit in REC OUT mode
while it is in the operating mode for ZONE2 are as follows:
• ZONE/DEVICE power button
• Muting button
• Master volume control button
NOTE
• Recordings you make are for your personal enjoyment and should
not be used for other purposes without permission of the copyright
holder.
• Input sources for which “Delete” is selected at “Source Delete”
(vpage100) cannot be selected.
1.AVR4311E2_ENG_6th_0810.indd 63 2010/08/12 10:12:05

Denon AVR-4311 Specifications

General

Type	AV Receiver
Number of channels	9.2
Output Power per Channel	140 W (8 ohms, 20 Hz - 20 kHz, 0.05% THD)
Frequency Response	10 Hz - 100 kHz (+1, -3 dB)
Total Harmonic Distortion	0.05%
Input Sensitivity/Impedance	200 mV / 47 kohms
Signal-to-Noise Ratio	102 dB
HDMI outputs	2
3D Support	Yes
Network features	AirPlay, DLNA
Audio DAC	24-bit/192kHz
Video Inputs/Outputs	Component
Audio Inputs/Outputs	Analog, Optical, Coaxial
Network Connectivity	Ethernet
Supported Audio Formats	Dolby TrueHD, DTS-HD Master Audio, FLAC, WAV, MP3, WMA, AAC
Dimensions (W x H x D)	434 x 195 x 427 mm
HDMI inputs	7 (1 on front)