EasyManuals Logo
Home>Denon>Receiver>AVR-X5200W

Denon AVR-X5200W User Manual

Denon AVR-X5200W
362 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #269 background imageLoading...
Page #269 background image
o
Add New Feature
Display new features that can be downloaded to this unit and perform
an upgrade.
Upgrade
Package:
Display the items to be upgraded.
Upgrade
Status:
Display a list of the additional functions provided by
the upgrade.
Upgrade Start:
Execute the upgrade process.
When the upgrade starts, the menu screen is shut
down. During the upgrade, the amount of upgrade
time which has elapsed is displayed.
0
See the Denon website for details about upgrades.
0
When the procedure is complete, “Registered” is displayed in this menu and
upgrades can be carried out. If the procedure has not been carried out, “Not
Registered” is displayed.
The ID number shown on this screen is needed when carrying out the
procedure.
The ID number can also be displayed by pressing and holding the main unit’s
u and INFO for at least 3 seconds.
0
If the upgrade is not successful, an error message identical to those in
“Firmware” - “Update” will appear on the display. Check the settings and
network environment and then perform the upgrade again.
Notes concerning use of “Update” and “Add New Feature”
0
In order to use these functions, you must have the correct system
requirements and settings for an Internet connection.
(v
p. 76)
0
Do not turn off the power until updating or upgrading is completed.
0
Approximately 1 hour is required for the updating/upgrading procedure
to be completed.
0
Once updating/upgrade starts, normal operations on this unit cannot
be performed until updating/upgrading is completed. Furthermore,
there may be cases where backup data is reset for the parameters,
etc., set on this unit.
0
If the update or upgrade fails, press and hold the X on the main unit for
more than 5 seconds, or remove and re-insert the power cord. “Update
Retry” appears on the display and update restarts from the point at
which update failed. If the error continues despite this, check the
network environment.
Information regarding the “Update” function and “Add New Feature” will be
announced on the Denon website each time related plans are defined.
Contents Connections Playback Settings Tips Appendix
269
Front panel Display Rear panel Remote Index

Table of Contents

Other manuals for Denon AVR-X5200W

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-X5200W and is the answer not in the manual?

Denon AVR-X5200W Specifications

General IconGeneral
Receiver typeSurround
Frequency range20 - 20000 Hz
Output impedance16 Ω
Speaker selectorA+B
Pre-out connectivityYes
Audio output channels- channels
Power output per channel (1KHz@6 Ohm)205 W
Power output per channel (20-20KHz@8 Ohm)140 W
HDMI in8
Remote (IR) input1
Composite video in5
Component video (YPbPr/YCbCr) in2
Number of HDMI outputs3
Connectivity technologyWired & Wireless
Speakers connectivity type-
Audio formats supportedAAC, AIFF, FLAC, MP3, WAV, WMA
Image formats supportedJPG
Supported radio bandsAM, FM
Internet radio services supportedSpotify, vTuner
Optical drive includedNo
Product colorSilver
Audio decodersDolby TrueHD, DTS 96/24, DTS Neo:X, DTS-ES, DTS-HD Master Audio
AC input voltage230 V
AC input frequency50 Hz
Power consumption (standby)0.1 W
Power consumption (typical)730 W
Weight and Dimensions IconWeight and Dimensions
Depth393 mm
Width434 mm
Height167 mm
Weight14200 g

Related product manuals