Denon AVR-X5200W User Manual

Symptom Cause / Solution Page
DTS Neo:X mode cannot
be selected.
0
It cannot be selected when “Speaker Config.” - “Surround” is set for “None”.
241
0
DTS Neo:X cannot be selected when using the headphones. －
Dolby Surround mode
cannot be selected.
0
Dolby Surround cannot be selected when using the headphones. －
Audyssey MultEQ
®
XT32,
Audyssey Dynamic EQ
®
,
Audyssey Dynamic
Volume
®
and Audyssey
LFC™ cannot be selected.
0
These cannot be selected when you have not performed Audyssey
®
Setup.
213
0
Switch to a sound mode other than “Direct” or “Pure Direct”. 147
0
These cannot be selected when using the headphones. －
Audyssey DSX
®
cannot be
selected.
0
It can be selected when using the front height or front wide speakers.
242
0
It can be selected when using the center speaker. 241
0
Switch the sound mode to Dolby sound mode or DTS sound mode. 146
0
This cannot be selected when using the headphones. －
0
This cannot be set when the input signal is a 2-channel source. －
“Restorer” cannot be
selected.
0
Check that an analog signal or PCM signal (Sample Rate = 44.1/48 kHz) is input. For playback of
multichannel signals such as Dolby Digital or DTS surround, “Restorer” cannot be used.
188
0
Switch to a sound mode other than “Direct” or “Pure Direct”.
147
No audio is output from
PRE OUT or speakers for
ZONE2/ZONE3.
0
In ZONE2/ZONE3, the audio can be played back when signals input from digital connectors (OPTICAL/
COAXIAL) are in 2ch PCM format.
－
0
In ZONE2, the audio can be played back when signals input from the HDMI connector are in 2ch PCM
format. To play back the audio in ZONE2 irrespective of the input signal format, set “HDMI Audio” in the
menu to “PCM”. Depending on the played back device, the audio may not be played back even with this
setting. In that case, set the audio format to “PCM (2ch)” on the played back device.
262
0
When listening to audio from a Bluetooth device in ZONE2/ZONE3, remove any obstructions between the
Bluetooth device and this unit and use it within a range of about 32.8 ft/10 m.
－
Contents Connections Playback Settings Tips Appendix
286
Front panel Display Rear panel Remote Index

Denon AVR-X5200W Specifications

General

Receiver type	Surround
Frequency range	20 - 20000 Hz
Output impedance	16 Ω
Speaker selector	A+B
Pre-out connectivity	Yes
Audio output channels	- channels
Power output per channel (1KHz@6 Ohm)	205 W
Power output per channel (20-20KHz@8 Ohm)	140 W
HDMI in	8
Remote (IR) input	1
Composite video in	5
Component video (YPbPr/YCbCr) in	2
Number of HDMI outputs	3
Connectivity technology	Wired & Wireless
Speakers connectivity type	-
Audio formats supported	AAC, AIFF, FLAC, MP3, WAV, WMA
Image formats supported	JPG
Supported radio bands	AM, FM
Internet radio services supported	Spotify, vTuner
Optical drive included	No
Product color	Silver
Audio decoders	Dolby TrueHD, DTS 96/24, DTS Neo:X, DTS-ES, DTS-HD Master Audio
AC input voltage	230 V
AC input frequency	50 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	730 W

Weight and Dimensions

Depth	393 mm
Width	434 mm
Height	167 mm
Weight	14200 g