02/2014 3 / 72
6159933910
Issue no: 04
1.1 - Statement of use ........................................... 5
1.2 - General instructions ...................................... 5
2.1 - CVIR II range................................................. 5
2.2 - Controllers ..................................................... 5
2.3 - CVIR II specications .................................... 5
2.4 - Communication ............................................. 5
2.5 - Tools .............................................................. 5
2.6 - CVIPC 2000 .................................................. 6
2.7 - CVINet ........................................................... 6
2.8 - PC Software evaluation version .................... 7
3.1 - Delivered equipment ..................................... 8
3.2 - Dimensions.................................................... 8
3.3 - Characteristics............................................... 8
3.4 - Front panel .................................................... 9
3.5 - Bottom panel ................................................. 9
4.1 - Installation ................................................... 10
4.1.1 - STOP signal ..................................................... 10
4.1.2 - Switch OFF....................................................... 10
4.1.3 - Wall mounting xation ...................................... 10
4.1.4 - Tool cable connection ....................................... 10
4.1.5 - 115/230 VAC cable connection .........................11
4.1.6 - Switch ON .........................................................11
4.2 - Start up ........................................................ 11
4.2.1 - How to enter or modify an alphanumeric eld ...11
4.2.2 - Language selection .......................................... 12
4.2.3 - Setting the date and time ................................. 12
4.2.4 - Contrast adjustment ......................................... 13
4.2.5 - Access code ..................................................... 13
4.2.6 - Activation code ................................................. 14
4.2.7 - Control screens ................................................ 15
4.2.8 - Results menu ................................................... 16
5.1 - CYCLES and PARAMETERS menu ........... 17
5.2 - LEARNING menu ........................................ 17
5.3 - CYCLES menu ............................................ 18
5.3.1 - Introduction....................................................... 18
5.3.2 - Selecting the cycle ........................................... 19
5.3.3 - Cycle general parameters ................................ 19
5.3.4 - Programming the phase ................................... 21
5.3.5 - Programming the parameters........................... 22
5.4 - Sequence menu .......................................... 28
5.5 - QUICK CYCLES menu................................ 29
5.6 - SPINDLE menu ........................................... 30
5.7 - STATION menu ........................................... 30
5.7.1 - STATION – General parameters ...................... 31
5.7.2 - INPUT / OUTPUT conguration ....................... 33
5.7.3 - INPUT menu ..................................................... 34
5.7.4 - OUTPUT menu ................................................. 36
5.7.5 - REVERSE menu .............................................. 38
5.8 - PERIPHERALS menu ................................. 39
5.8.1 - SERIAL PORT menu ........................................ 39
5.8.2 - ETHERNET CONFIGURATION menu ............. 39
5.8.3 - ETHERNET SOCKET 1 menu ......................... 40
5.8.4 - ETHERNET SOCKET 2 menu ......................... 40
5.8.5 - ETHERNET SOCKET 3 menu ......................... 40
5.8.6 - PLC menu ........................................................ 40
5.8.7 - REPORT OUTPUT menu ................................. 41
5.8.8 - BAR CODE menu............................................. 42
5.8.9 - CVINET menu .................................................. 42
5.8.10 - TOOLSNET menu .......................................... 43
5.9 - CONTROLLER menu .................................. 44
5.10 - CURVES menu ......................................... 45
6.1 - MAINTENANCE menu ................................ 46
6.1.1 - TEST menu ...................................................... 46
6.1.2 - CHANNEL TEST menu .................................... 47
6.1.3 - COUNTERS menu ........................................... 47
6.1.4 - CALIBRATION menu ........................................ 48
6.2 - SERVICE menu ........................................... 49
6.3 - Maintenance operation ................................ 49
6.3.1 - Changing the memory battery .......................... 49
6.3.2 - Desoutter Tool and Account Services ............... 49
6.4 - Spare parts .................................................. 50
To Next Page
Loading...
Need help?
General
