Need help?Do you have a question about the Dickey-John PM400 and is the answer not in the manual?
Identifies important safety messages in the manual and alerts to potential injury or death.
Indicates a potentially hazardous situation that could result in death or serious injury if not avoided.
Indicates a potentially hazardous situation that could result in minor or moderate injury if not avoided.
Guides on setting up the number of rows, row spacing, and ground speed constant for monitor operation.
Details the process of configuring the spacing between planter rows for accurate monitoring.
Explains how to calibrate or manually enter ground speed for accurate speed-based monitoring.
Requires input for system function: Planter Setup screen and Ground Speed Setup screen.
Configures rows as ON (population), OFF (split), Flow (blockage), or Disabled for monitoring.
Covers calibration factor, calibration aid, manual ground speed, and max speed alarm.
Defines population features: target, min/max alarm limits, adjustment factor, and response rate.
Triggers alarms when seed flow drops below population limits, indicating over or under population.
Provides tools for monitoring planting, accessed via the Operate key, with customizable upper/lower windows.
Activates when seed level drops below sensor mounting level; can be silenced by Alarm Cancel.
Triggers when less than 2 seeds/sec detected per tube; indicates poor connection or faulty sensor.
Unique identifier (8 chirps) for no seed flow from any row unit when ground speed is detected.
Triggers when seed flow drops below population limits, indicating over or under population.
Triggers when fan speed exceeds or falls below set limits; alarm can be silenced but reactivates if unresolved.
Triggers when shaft speed exceeds or falls below set limits; alarm can be silenced but reactivates if unresolved.
Triggers when flow inputs exceed or fall below set limits; alarm can be silenced but reactivates if unresolved.
Triggers when planting is detected with no ground speed reported; due to poor connection or defective sensor.
Addresses probable causes like blown fuse, poor battery connection, low voltage, or defective console.
Troubleshoots alarms during proper planting, citing sensor dirt, faulty harness, or console issues.
Addresses ground speed alarms during forward movement, caused by sensor failure or console issues.
Explains causes for high ground speed alarms, such as incorrect constant or uncalibrated sensor.
Identifies important safety messages in the manual and alerts to potential injury or death.
Indicates a potentially hazardous situation that could result in death or serious injury if not avoided.
Indicates a potentially hazardous situation that could result in minor or moderate injury if not avoided.
Guides on setting up the number of rows, row spacing, and ground speed constant for monitor operation.
Details the process of configuring the spacing between planter rows for accurate monitoring.
Explains how to calibrate or manually enter ground speed for accurate speed-based monitoring.
Requires input for system function: Planter Setup screen and Ground Speed Setup screen.
Configures rows as ON (population), OFF (split), Flow (blockage), or Disabled for monitoring.
Covers calibration factor, calibration aid, manual ground speed, and max speed alarm.
Defines population features: target, min/max alarm limits, adjustment factor, and response rate.
Triggers alarms when seed flow drops below population limits, indicating over or under population.
Provides tools for monitoring planting, accessed via the Operate key, with customizable upper/lower windows.
Activates when seed level drops below sensor mounting level; can be silenced by Alarm Cancel.
Triggers when less than 2 seeds/sec detected per tube; indicates poor connection or faulty sensor.
Unique identifier (8 chirps) for no seed flow from any row unit when ground speed is detected.
Triggers when seed flow drops below population limits, indicating over or under population.
Triggers when fan speed exceeds or falls below set limits; alarm can be silenced but reactivates if unresolved.
Triggers when shaft speed exceeds or falls below set limits; alarm can be silenced but reactivates if unresolved.
Triggers when flow inputs exceed or fall below set limits; alarm can be silenced but reactivates if unresolved.
Triggers when planting is detected with no ground speed reported; due to poor connection or defective sensor.
Addresses probable causes like blown fuse, poor battery connection, low voltage, or defective console.
Troubleshoots alarms during proper planting, citing sensor dirt, faulty harness, or console issues.
Addresses ground speed alarms during forward movement, caused by sensor failure or console issues.
Explains causes for high ground speed alarms, such as incorrect constant or uncalibrated sensor.
General| Brand | Dickey-John |
|---|---|
| Model | PM400 |
| Category | Controller |
| Language | English |
To Next Page
