To Next PageTo Next PageWhat to do if Directed DIRECTECHS DS3+ ISO 1 not detected?
If the Yellow/Black wire did not detect the expected signal, refer to “Installation (wiring diagrams & vehicle wiring reference charts)” to check the connections.
What does it mean if Directed Automobile Accessories PTS shutdown error?
The PTS output from the module was not activated due to safety protection.
Why is Directed DIRECTECHS DS3+ Automobile Accessories showing 'Speed was detected'?
The vehicle was detected as moving, which prevents the system from shutting it down.
What to do if Directed DIRECTECHS DS3+ shows CAN1 not detected?
If the Directed Automobile Accessories module experiences a CAN1 detection failure, check the CAN1 Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on and try again. If your installation doesn't need this connection, skip this step by pressing the programming button 5 times.
Why is smart key not detected by Directed Automobile Accessories?
The smart key was not detected, which prevents the system from shutting down the vehicle.
What to do if Directed DIRECTECHS DS3+ ISO 2 is not detected?
If the Orange/Black wire did not detect the expected signal, refer to 'Installation (wiring diagrams & vehicle wiring reference charts)' to check the connections.
How to fix CAN1 not detected error in Directed DIRECTECHS DS3+?
The CAN1 Tan and Tan/Black wire connections need to be checked. Try waking up the data bus by turning the ignition on and trying again. If your installation doesn't need this connection, you can skip this step by pressing the programming button 5 times.
What to do if CAN1 is not detected in Directed Automobile Accessories?
Check the connections of the CAN1 Tan and Tan/Black wires. Try waking up the data bus by turning the ignition on and attempting the process again. If your setup doesn't need this connection, you can bypass it by pressing the programming button 5 times.
What to do if CAN2 is not detected on Directed DIRECTECHS DS3+?
Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.
What to do if Directed Automobile Accessories bypass data not detected?
Check the bypass line connection. If there's more than one wire, ensure they aren't inverted. Also, make sure the vehicle still operates correctly using the factory key.
General| Type | Remote Start System |
|---|---|
| Channels | 3 |
| Remote Confirmation | Yes |
| Weight | 0.5 lbs |
| Relay Outputs | 3 |
| Compatibility | Compatible with most vehicles |
| Voltage Range | 12V |
| Operating Temperature | -40°F to 185°F |
| Outputs | 12-pin harness |
Explains web, desktop, and mobile app configuration options for the DS3/DS4+ modules.
Discusses firmware updates, installation notes, and critical warnings for the installation.
Table mapping vehicle models to keyless access control unit locations.
Details for connecting the optional starter disable feature.
Wiring details for the 8-pin data harness (H1).
Wiring details for the 22-pin analog input/output harness (H2).
Wiring details for the 12-pin main harness (H3).
Wiring details for the 10-pin relay harness (H4) and 2-pin RF port harness (H5).
Wiring details for the 4-pin D2D harness (H6) and 2-pin sensor harness (H7).
Instructions for entering and completing the remote pairing process.
Details on temperature sensors, combo sensors, and RF systems.
Information on using the system with Directed SmartStart.
Configuring manual transmission ready mode initialization and completion sequences.
Using programmable outputs for clutch bypass or starter functions.
Additional connection requirements for manual transmission.
Interpreting LED indicators during module programming and error codes.
Understanding LED feedback for synchronization, status, commands, and shutdown codes.
Steps for tach learning with data or hardwired tach sources.
Instructions for initializing and using Virtual Tach for remote start.
Special settings for hybrid vehicles when using Virtual Tach.
Methods for sending commands like lock, unlock, and remote start.
Procedure for seamless vehicle takeover after remote start.
Explains vehicle takeover and pit stop/idle mode features.
Overview of features controllable via the SmartStart application.
