What to do if Directed Automobile Accessories has a bypass processing error?
If the bypass calculation failed, reset the module and try again. If the condition persists, please contact Technical Support.
What does it mean if Directed Automobile Accessories is waiting to begin programming sequence?
It means you should ensure the correct programming procedure is being followed.
What to do if Directed DIRECTECHS DS3+ Automobile Accessories initialization failed?
Reset the module and complete the programming again. If the issue persists, please contact Technical Support.
What to do if J1850 not detected on Directed Automobile Accessories?
Check the J1850 wire connection. Wake up the data bus by turning the ignition on and try again.
What to do if CAN2 is not detected on Directed DIRECTECHS DS3+?
Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.
What to do if Directed Automobile Accessories bypass data not detected?
Check the bypass line connection. If there's more than one wire, ensure they aren't inverted. Also, make sure the vehicle still operates correctly using the factory key.
What to do if CAN1 is not detected on Directed DIRECTECHS DS3+ Automobile Accessories?
Check the CAN1 Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.
What to do if Directed DIRECTECHS DS3+ Automobile Accessories shows bypass data not detected?
If the Directed Automobile Accessories system experiences a bypass data detection issue, check the bypass line connection. If multiple wires are used, ensure they are not inverted. Also, make sure the vehicle still operates correctly using the factory key.
What to do if Directed DIRECTECHS DS3+ CAN1 is not detected?
Check the CAN1 Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.
Why Directed DIRECTECHS DS3+ Automobile Accessories says 'Brake was not detected'?
The brakes were not detected, which prevents the system from shutting down the vehicle.
Explains web, desktop, and mobile app configuration options for the DS3/DS4+ modules.
Discusses firmware updates, installation notes, and critical warnings for the installation.
Table mapping vehicle models to keyless access control unit locations.
Details for connecting the optional starter disable feature.
Wiring details for the 8-pin data harness (H1).
Wiring details for the 22-pin analog input/output harness (H2).
Wiring details for the 12-pin main harness (H3).
Wiring details for the 10-pin relay harness (H4) and 2-pin RF port harness (H5).
Wiring details for the 4-pin D2D harness (H6) and 2-pin sensor harness (H7).
Instructions for entering and completing the remote pairing process.
Details on temperature sensors, combo sensors, and RF systems.
Information on using the system with Directed SmartStart.
Configuring manual transmission ready mode initialization and completion sequences.
Using programmable outputs for clutch bypass or starter functions.
Additional connection requirements for manual transmission.
Interpreting LED indicators during module programming and error codes.
Understanding LED feedback for synchronization, status, commands, and shutdown codes.
Steps for tach learning with data or hardwired tach sources.
Instructions for initializing and using Virtual Tach for remote start.
Special settings for hybrid vehicles when using Virtual Tach.
Methods for sending commands like lock, unlock, and remote start.
Procedure for seamless vehicle takeover after remote start.
Explains vehicle takeover and pit stop/idle mode features.
Overview of features controllable via the SmartStart application.
General| Type | Remote Start System |
|---|---|
| Channels | 3 |
| Remote Confirmation | Yes |
| Weight | 0.5 lbs |
| Relay Outputs | 3 |
| Compatibility | Compatible with most vehicles |
| Voltage Range | 12V |
| Operating Temperature | -40°F to 185°F |
| Outputs | 12-pin harness |
To Next Page