dji Mavic 3 User Manual

DJI Mavic 3 User Manual
40
©
2021 DJI All Rights Reserved.
Charging the Battery
Use a USB-C cable to connect the provided
charger to the USB-C port of the remote
controller. It takes approximately four hours to
fully charge the remote controller.
Controlling the Gimbal and Camera
Shutter/Record Button: Press once take a photo
or to start or stop recording.
Photo/Video Toggle: Press once to switch
between photo and video mode.
Gimbal Dial: Use to control the tilt of the gimbal.
Press and hold the customizable button in order
to be able to use the gimbal dial to adjust the
zoom in explore mode.
RC-N1
Built into the remote controller is DJI'S long-range tranmission OcuSync 2.0 technology, offering a
maximum transmission range of 15 km and displaying video from the aircraft to DJI Fly on a mobile
device at up to 1080p 60fps (depending on phone type). The aircraft and camera are easy to control
using the onboard buttons and the detachable control sticks make the remote controller easier to store.
In a wide-open area with no electromagnetic interference, the aircraft uses O3+ and the remote
controller uses OcuSync 2.0 to smoothly transmit video links at up to 1080p 60fps (depending on
phone type). The remote controller works at both 2.4 GHz and 5.8 GHz, automatically selecting the best
transmission channel.
The built-in battery has a capacity of 5200 mAh and energy of 18.72 Wh and a maximum run time of
6 hours. The remote controller charges the mobile device with a charging ability of 500 mA@5 V. The
remote controller automatically charges Android devices. For iOS devices, rst make sure that charging
is enabled in DJI Fly. Charging for iOS devices is disabled by default and needs to be enabled each time
the remote controller is powered on.
Compliance Version: The remote controller is compliant with local regulations.
Control Stick Mode: The control stick mode determines the function of each control stick movement.
Three pre-programmed modes (Mode 1, Mode 2, and Mode 3) are available and custom modes can
be congured in DJI Fly. The default mode is Mode 2.
Using the Remote Controller
Powering On/O
Press the power button once to check the current
battery level. Press once, then again, and hold
to power the remote controller on or off. If the
battery level is too low, recharge before use.
Gimbal Dial
Shutter/Record
Button
Photo/Video
Toggle
Customizable
Button

dji Mavic 3 Specifications

General

Type	Quadcopter
Product color	Black
Maximum speed	19 m/s
GPS (satellite)	Yes
Number of rotors	4 rotors
Maximum tilt angle	35 °
Hovering time (max)	40 min
Maximum flight time	46 min
Maximum ascent speed	8 m/s
Maximum descent speed	6 m/s
Maximum weight capacity	- kg
Maximum wind resistance	12 m/s
Maximum operating distance	30000 m
Maximum pitch angular velocity	200 °/sec
USB ports quantity	2
Operating frequency	2400000 MHz
Battery voltage	15.4 V
Battery capacity	5000 mAh
Megapixel	20 MP
Sensor type	CMOS
Video resolutions	1920 x 1080, 3840 x 2160, 4096 x 2160 pixels
Maximum frame rate	120 fps
Camera shutter speed	8 - 1/8000 s
Image formats supported	DNG, JPEG
Video formats supported	H.264, H.265
Maximum image resolution	5280 x 3956 pixels
Maximum video resolution	5120 x 2700 pixels
Field of view (FOV) angle	84 °
Operating temperature (T-T)	-10 - 40 °C
Internal memory	8 GB
Compatible memory cards	MicroSD (TransFlash)
Built-in processor	-
Moving control functions	Backward, Downward, Forward, Upward

Weight and Dimensions

Depth	221 mm
Width	96.3 mm
Height	90.3 mm
Weight	895 g
Battery weight	335.5 g