Dräger Atlan A350 XL - Page 137

332 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Instructions for use | Atlan A300, A300 XL, A350, A350 XL SW 1.0n 137

Tests

5. Set the O2 switch to Aux. O2.

8.4.1 Vaporizers

For each vaporizer, check:

1. The locking lever points left, indicating the vaporizer is locked.

2. The filling inlet is closed.

351043510535108

Table of Contents

Default Chapter3
- Table of Contents3
1 Information about this Document7
- Typographical Conventions7
- Use of Terms7
- Illustrations7
- Trademarks7
2 Safety-Related Information9
- Intended Use9
- Indications9
- Contraindications9
- Environments of Use10
- Essential Performance Features10
- User Group Requirements11
- Information on Safety Instructions and Precautionary Statements11
- Safety Instructions12
- Additional Information14
3 Overview15
- Hardware15
- Functional Scope31
- Gas Flow Diagram42
4 Assembly and Preparation45
- Safety Instructions45
- Mounting of Accessories52
- Before First Operation55
- Intrahospital Transport59
- Gas Supply59
- Connecting to the Gas Scavenging System65
- Preparation for an Operation Day / after Cleaning and Sterilization67
- Selecting and Connecting Patient-Specific Accessories67
- Connecting and Replacing Consumables75
5 Operating Concept79
- Screen79
- Color Concept83
- Selecting and Setting84
6 Getting Started86
- Safety Instructions86
- Turning on the Device86
- Checking the Device Configuration86
- Checking the Operational Readiness87
- Emergency Start-Up88
7 Operation89
- Safety Instructions89
- Starting the Therapy93
- Adjusting the Therapy96
- Special Forms of Therapy100
- Using Fields with Special Functions103
- Customizing the Screen Display107
- Displaying Additional Data113
- Setting the Volume115
- Adjusting the Alarms116
- Changing the Patient Data119
- Exporting Data119
- Other Settings120
- Ending the Therapy122
- Change of Patient124
8 Tests126
- Status of the Device Functions126
- Available Test Types127
- Performing the Tests127
- Checklist in the Walk-Through Mode136
9 Ending Operation151
- At the End of the or Day151
- Storing the Device151
- Disconnecting the Mains Power Supply151
10 Alarms152
- Safety Instructions152
- Displaying Alarms152
- Response to Alarms154
- Adopting Alarm Settings When Changing the Ventilation Mode159
- Alarm Delay and Alarm Escalation160
- Activation of Alarms after Breath Detection163
- Intelligent Alarm Behavior164
11 Configuration165
- Device Settings165
- Setting the Date and Time165
- Specifying the Start Settings166
- Transferring Device Configurations181
- Activating Software Options182
- Overview of Configurable Screen Contents184
12 Troubleshooting190
- Leakage190
- Power Supply Failure191
- Failure of the Gas Supply192
- Failure of Fresh-Gas Delivery (Electronically Controlled Gas Mixture)194
- Failure of the Piston Ventilator195
- Failure of the O 2 Sensor195
- Flow Measurement Failure198
- Screen Fault or Failure of the Graphical User Interface198
- Complete Failure198
- Problems with the Active Anesthetic Gas Receiving System (AGS)199
- Cylinder Pressure Reducer201
- Support Request201
- Alarm - Cause - Remedy201
13 Reprocessing222
- Safety Instructions222
- Information on Reprocessing223
- Classifications for Reprocessing224
- Reprocessing List225
- Reprocessing Procedures225
- Preparation227
- Surface Disinfection with Cleaning229
- Disassembly230
- Disassembling the Breathing System238
- Machine Reprocessing242
- Fitting and Assembly249
- Preparation before the Next Use258
- Brief Instructions for Reprocessing260
14 Service262
- Safety Instructions262
- Definition of Service Terminology262
- Inspection262
- Maintenance265
- Repair265
15 Disposal266
- Safety Instructions266
- Disposing of the Device266
- Disposing of Accessories266
16 Technical Data267
- Safety Instructions267
- General Information268
- Ambient Conditions268
- Fresh-Gas Delivery269
- Fresh-Gas Delivery with Electronically Controlled Gas Mixer269
- Fresh-Gas Delivery with Mechanically Controlled Gas Mixer270
- Ventilator270
- Breathing System272
- External Fresh-Gas Outlet274
- Anesthetic Gas Receiving System (AGS)274
- Active AGS274
- Passive AGS275
- Measuring Systems and Displays275
- Gas Measurement279
- Gas Measurement with279
- Gas Measurement with O281
- Sensor281
- Operating Characteristics283
- Interfaces and Ports287
- Relevant Standards289
- Diagrams290
- EMC Declaration291
- Device Combinations293
- Emission of High-Frequency Energy293
- Connections to IT Networks294
- Open-Source Software297
17 Principles of Operation297
- Safety Instructions297
- Description of the Ventilation Modes298
- Description of the Ventilation Drive307
- Improving the CO 2 Measurement by Means of an HME Filter308
- Minimum O 2 Delivery310
- Influence of Patient Category, Weight, and Age on Device Behavior311
- Support of Infinity ID Accessories312
- Schematic Illustration of the Acoustic Signals313
18 Annex314
- Abbreviations314
- Symbols317
- Product Labels322
- Overview of the Menu Structure323
19 Password325
- Configuration Password for Atlan A300, A300 XL, A350, A350 XL Software 1.0N325
Index327

Related product manuals

Dräger Atlan A350

Preview: Dräger Atlan A300

Dräger Atlan A300

Preview: Dräger Atlan

Preview: Dräger Atlan A100

Dräger Atlan A100

Preview: Dräger AGS

Preview: Dräger Apollo

Preview: Dräger Perseus A500

Dräger Perseus A500

Dräger Aquapor H300

Preview: Infinity Acute Care System M540

Infinity Acute Care System M540

Infinity Acute Care System Workstation Critical Care

Preview: Dräger Savina 300

Dräger Savina 300

Preview: Dräger Isolette 8000 plus

Dräger Isolette 8000 plus