Drivecon XT Series - Monitoring; G4.2 Analog I;O; G4.5 Fault Counter; G4.7 Digital Input

11
Owner's Manual
Drivecon Toll Free Ph: 1-800-374-8266
Drivecon reserves the right to alter or amend the above information without notice
Monitoring
Below are listed the parameters of Group G4 Monitoring. For example, operation of analog and
digital inputs can be verified with monitoring parameters. After power off and on the display returns
as default to V4.22 Output Frequency.
G4.1 Parameter Backup G4.7 Digital Input
B4.1.1 Load Default Par
G4.7.1 DI Status
B4.1.2 Save User Par
V4.7.1.1 S1
B4.1.3 Load User Par
V4.7.1.2 S2
G4.1.4 Factory default
V4.7.1.3 DIA3
B4.1.4 Save Default Par
V4.7.1.4 DIA4
G4.2 Analog I/O
V4.7.1.5 DIA5
V4.2.1 Ain1 Value V V4.7.1.6 OK
V4.2.2 Ain2 Value V V4.7.1.7 DID1
V4.2.3 Aout1 Value mA V4.7.1.8 DID2
V4.2.4 Aout2 Value V V4.7.1.9 DID3
G4.3 Relay Output
V4.7.1.10 DID4
V4.3.1 ROB1 State V4.7.1.11 DID5
V4.3.2 ROB2 State K7
G4.7.2 DI Function
V4.3.3 ROC1 State V4.7.2.1 DIA3 Function
V4.3.4 ROD1 State V4.7.2.2 DIA4 Function
V4.3.5 ROE1 State V4.7.2.3 DIA5 Function
V4.3.6 ROE2 State V4.7.2.4 DID1 Function
V4.3.7 ROE3 State V4.7.2.5 DID2 Function
G4.4 Operate Counters
V4.7.2.6 DID3 Function
Operate counters are not used V4.7.2.7 DID4 Function
G4.5 Fault Counter
V4.7.2.8 DID5 Function
R4.5.1 Fault Counter V4.7.3 Basic Board
V4.5.2 Total Faults V4.7.4 Extension Board
V4.5.3 Selected Faults
G4.8 SSU
G4.6 Bus Control
V4.8.1 Overspd Lim 1 %
V4.6.1 S1 V4.8.2 Overspd Lim 2 %
V4.6.2 S2
G4.9 Service
V4.6.3 Motor Set 2 V4.9.1 Phase U Curr A
V4.6.4 Second Speed Lim V4.9.2 Phase V Curr A
V4.6.5 Field Weakening V4.9.3 Phase W Curr A
V4.6.6 Alt Control Mode V4.9.4 Encoder Speed Hz
V4.6.7 Brake Feedback
G4.10 Sway control
V4.6.8 Ramp 2 V4.10.1 Swing Time s
V4.6.9 Torque Limit V4.10.2 Pendulum Length m
V4.6.10 AP V4.10.3 StoppingDistance m
V4.6.11 Slow Limit S11 V4.11 Freq Ref Hz
V4.6.12 Slow Limit S21 V4.12 Speed Req Hz
V4.6.13 End Limit S12 V4.13 Distance Counter m
V4.6.14 End Limit S22 V4.14 DC-link Voltage V
V4.6.15 Brake Pedal V4.15 Heat Sink Temp °C
V4.6.16 S-Curve Inhibit V4.16 MotorTemperature %
V4.6.17 Tare V4.17 Motor Power %
V4.6.18 Inching V4.18 Motor Voltage V
V4.6.19 SlackCableByPass V4.19 Motor Torque %
V4.6.20 Brake Pedal 2 V4.20 Motor Current A
V4.6.21 Synchronizing V4.21 Motor Speed rpm
V4.6.22 Speed Reference V4.22 Output Frequency Hz
V4.6.23 Torque Reference
G4.23 Multimonitor
V4.6.24 Speed Correction N4.23.1 Multimonitor
V4.6.25 Ramp Reference
V4.6.26 Torque Limit Ref
V4.6.27 Speed Limit Ref
V4.6.28 Load Feedback
V4.6.29 Sway Ctrl Height
V4.6.30 Calibration Pos
V4.6.31 Profibus Status