i
Table of Contents
Section 1: Introduction 1
1.1 Out Of The Box .......................................................................... 1
1.2 Specifications and Features ..................................................... 1
Section 2: Installation and Wiring 2
2.1 Planning the System ................................................................. 2
2.2 Terminal Descriptions .............................................................. 2
2.3 Wire Routing for Power and Non-Power Limited ............... 2
2.4 Current Ratings – Alarm Control Panel and Modules ........ 2
2.5 Combus Operation and Wiring .............................................. 3
2.6 Zone Wiring ............................................................................... 4
2.7 Specialized Zone Wiring .......................................................... 4
2.8 Programmable Output Wiring ................................................ 5
2.9 AML Device Wiring .................................................................. 5
2.10 Wiring Powered Devices (AUX, SAUX+) .............................. 6
2.11 Telephone Line Wiring ............................................................. 6
2.12 Bell Output Wiring (BELL+ and BELL-) ................................ 7
2.13 Earth Ground Wiring ............................................................... 7
2.14 Applying Power (AC and Battery) ......................................... 7
2.15 Lithium Batteries ....................................................................... 8
Section 3: How to Program 9
3.1 Introduction to Programming ................................................. 9
3.2 Programming by Reference Number ..................................... 9
3.3 Programming Decimal Data .................................................... 9
3.4 Programming Hexadecimal Data ......................................... 10
3.5 Programming Toggle Options .............................................. 10
Section 4: Module Enrollment 11
4.1 Enrolling Keypads and Modules .......................................... 11
4.2 Deleting Modules .................................................................... 11
4.3 Confirming Modules .............................................................. 11
4.4 Enrolling AML Devices .......................................................... 12
Section 5: Partitions and Zones 13
5.1 Zone Supervision .................................................................... 13
5.2 Creating Partitions .................................................................. 13
5.3 Adding Zones to Partitions ................................................... 14
5.4 Zone Programming ................................................................. 14
5.5 Bypass Grouping ..................................................................... 17
Section 6: Keypad Operation 19
6.1 Partition Keypads .................................................................... 19
6.2 Global Keypads ....................................................................... 19
6.3 Keypad Toggle Options ......................................................... 19
6.4 Keypad Time-out .................................................................... 20
6.5 Keypad Blanking ..................................................................... 20
6.6 Fire, Auxiliary and Panic Keys .............................................. 20
6.7 Keypad Lockout ...................................................................... 20
6.8 Keypad Tampers ..................................................................... 21
6.9 Alarm Memory Display ......................................................... 21
6.10 Zone Bypass Display .............................................................. 21
6.11 Function Key Programming .................................................. 21
Section 7: Installer and Access Codes 23
7.1 Installer’s Code ........................................................................ 23
7.2 Installer-Programmed Access Codes ................................... 23
7.3 Programming Access Codes .................................................. 23
7.4 Modify An Existing Code ...................................................... 25
7.5 Change User Code Options ................................................... 25
7.6 Delete An Existing Code ........................................................ 25
7.7 Special Codes ........................................................................... 26
7.8 Guard Code .............................................................................. 26
7.9 Access Code Options .............................................................. 26
7.10 Access Levels ........................................................................... 27
Section 8: Arming and Disarming 28
8.1 Arming and Disarming Options ........................................... 28
8.2 Automatic Arming .................................................................. 28
8.3 Close Time Timer (CTT Duration) ........................................ 28
8.4 Disarm Delay ........................................................................... 28
8.5 Dual Users For Disarming ..................................................... 29
Section 9: Entry and Exit Delay 30
9.1 Entry and Exit Delay Times ................................................... 30
9.2 Entry and Exit Delay Options ............................................... 30
Section 10: System Programming 31
10.1 AC/DC Power Options .......................................................... 31
10.2 Bell Circuit Supervision ......................................................... 31
10.3 Clock Options .......................................................................... 31
10.4 Event Messages ....................................................................... 31
10.5 Swinger Shutdown .................................................................. 32
10.6 Tampers .................................................................................... 32
10.7 Telephone Line Supervision .................................................. 32
10.8 Test Transmissions .................................................................. 32
10.9 Transmission Delay ................................................................ 33
10.10 Cross Zone (Police Code) Alarm ......................................... 33
10.11 System Label ........................................................................... 33
10.12 Hourly Print ............................................................................ 33
Section 11: Programmable Outputs 34
11.1 Main Panel Outputs ................................................................ 34
11.2 Programming Output Options for Modules ....................... 34
11.3 Programmable Output Options ............................................ 34
11.4 Output Pulse Times ................................................................ 37
Section 12: Communications Programming 38
12.1 Telephone Numbers ............................................................... 38
12.2 Account Numbers ................................................................... 38
12.3 Dialing Parameters .................................................................. 38
12.4 Communicator Toggle Options ............................................ 38
12.5 Dialer Direction ....................................................................... 40
12.6 Communicator Formats ......................................................... 40
12.7 Reporting Codes ...................................................................... 41
Section 13: Downloading 42
13.1 Downloading Options ............................................................ 42
13.2 Periodic Call-up ....................................................................... 42
13.3 PC-Link ..................................................................................... 42
Section 14: Event Scheduling 43
14.1 Date Schedules ......................................................................... 43
14.2 Holiday Groups ....................................................................... 43
14.3 Open/Close Suppression ....................................................... 43
14.4 Arming/Disarming Schedules .............................................. 44
14.5 Scheduled AMS-220/220T Smoke Detector Test ................ 44
14.6 CTT Schedule ........................................................................... 44
14.7 Seismic Schedule ..................................................................... 44
Section 15: LINKS Communications 45
15.1 LINKS1000 (Cellular Communications) .............................. 45
15.2 LINKS2XXX (Long-range Radio Communications) .......... 45
15.3 T-Link TCP/IP Communications) ........................................ 45
NEW!
NEW!
NEW!
NEW!
NEW!
NEW!
To Next Page
Loading...
Need help?
General
