41
immediately after the zone event. All fourteen characters of
the label will be transmitted even if the programmed label
is less than 14 characters.
NOTE: Installer must ensure that this feature is supported
by the central station receiver(s). When using this option
the zone labels can only use the following ASCII characters:
SIA 1 Account#
Ref #: [000401] and scroll to option
If the ’SIA 1 Account#’ toggle option is enabled, the SIA
communication format will send the system ID code along
with the partition number with each data transmission. If
disabled, the communication format will use all eight Parti-
tion ID codes to identify partition events. If this option is
enabled, partition account numbers are not required.
Please refer to Appendix A ’Reporting Codes’ and Appen-
dix B ’Zone Reporting Codes for a list of SIA identifiers.
SIA Transmission 4-Digit Option
This option controls whether the panel will transmit three
or four digits for the reporting code when using SIA. Four
digits are required to properly identify users 1000-1500.
Otherwise these users will be identified as 999.
NOTE: Before choosing this option, you must ensure that
this feature is supported by the central station receiver(s).
Pager Formats
The Pager format can be used for latchkey operation to
notify a parent when a child comes home from school or to
notify a key holder that an alarm has occurred. In North
America, the Pager Format 3 should be used.
When programming the Pager telephone number, special
programming is required in order for the panel to transmit
the page successfully. Pauses, [*] key presses and [#] key
presses may be required. For more information about pro-
gramming these special items, see 5.1 ‘Zone Supervision‘.
The panel will only make one attempt to send a page for
each event. There are three types of pager formats:
•Pager Format 1
Pager Format 1 Pager Format 1
Pager Format 1 (Semadigit) transmits seven DTMF dig-
its for each event. Each round transmits a 4-digit
account code followed by a 2-digit reporting code fol-
lowed by the DTMF Character [#]. Only one event is
communicated per call. This format requires an initial
handshake of 440Hz and a kissoff handshake of 1400Hz.
NOTE: Do not use this format in North America.
•Pager Format 2
Pager Format 2 Pager Format 2
Pager Format 2 (Semaphone) transmits no data. The sys-
tem will call the number programmed once for every
event that occurs. This format is intended to be used with
a pager but can be used to call a private residence. This
format will sound the line every two seconds after dial-
ing the telephone number. Although events are not iden-
tified, the recipient is made aware of an alarm. Only one
event is communicated per call. No handshake or kissoff
signals are required for this format.
NOTE: Do not use this format in North America. Do not use
this format with 1300 Hz ID.
• Pager Format 3
Pager Format 3 Pager Format 3
Pager Format 3 is similar to Pager Format 1 except that
no handshake or kissoff signals are required.
NOTE: Do not use this format with 1300 Hz ID. UL has only
verified compatibility of the PC4020 with the Silent Knight
model 9000, Ademco model 685, Linear model 3060 and
Radionics model D6500.
12.7 Reporting Codes
Reporting codes must be programmed in order for the
panel to report events to the central station.
Reporting codes are two digits and can use hexadecimal
digits A through F. Some communicator formats only
require one digit (see Section 12.6 ’Communicator For-
mats’). To disable a reporting code, program it with ’FF’
(default setting) or ’00’. Pressing the [*] key when entering
the code will call up a menu for hex digit entry. For instruc-
tions on programming HEX digits, see 3.4 ‘Programming
Hexadecimal Data‘.
All reporting codes are listed and described in Appendix A
’Reporting Codes’.
A - Z ASCII 65 to 90
a - z ASCII 97 to 122
0 - 9 ASCII 48 to 57
, ASCII 44
- ASCII 45
. ASCII 46
: ASCII 58
<space> ASCII 32
To Next Page
Loading...
