EasyManuals Logo

DSC PowerSeries PC585 User Manual

DSC PowerSeries PC585
52 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #38 background imageLoading...
Page #38 background image
34
PGM Output Attributes
(Section 5.11 “PGM Output Options” )
Program only the following attributes for the PGM Options listed. All others will be ignored. PGM Options are programmed in
[009]. PGM Attribute Defaults (Y = Attribute ON; N = Attribute OFF):
Section PGM Output 1 2 3 4 5 6 7 8
#Type*
[141] 1 ( )
I________I I________| I________| I________| I________| I________| I________| I________I
[142] 2 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
*Record here based on programming in [009].
[160] Maximum Dialing Attempts to Each Telephone Number
(Section 5.5 “Communicator – Dialing” )
Default: 007 I_______I_______I_______I Valid entries are 001-015 attempts (do not enter 000).
[161] Post Dial Wait for Handshake (All Formats)
(Section 5.5 “Communicator – Dialing” )
Default: 040 I_______I_______I_______I Valid entries are 001-255 seconds
[164] PGM Output Timer
(Section 5.11 “PGM Output Options” )
Default: 005 I_______I_______I_______I Valid entries are 001-255 seconds
Attribute: 1 2 3 4 5
ON
Output enabled True Output Follows Timer Code Req.
OFF
Output disabled Inverted On / Off No Code Req.
PGM Option
[01] Burg. / Fire Bell Y Y
[03] Sensor Reset Y Y N
[05] Armed Status Y Y
[06] Ready To Arm Y Y
[07] Kypd Bzz Follow Y Y
[08] Courtesy Pulse Y Y
[11] System Tamper Y
[12] TLM and Alarm Y
[13] Kiss-off Y
[14] Gnd Strt Pulse Y
[15] Remote Op. Y
[16] GSM1000 Support Y
[17] Away Armed Status Y Y
[18] Stay Armed Status Y Y
[19] Comm. Output #1 Y Y Y Y
[20] Comm. Output #2 Y Y Y N
[21] Comm. Output #3 Y Y Y N
[22] Comm. Output #4 Y Y Y N
[23] Silent 24 Hr Y
[24] Audible 24 Hr Y
[26] Battery Test Y
[27] Police Code Y Y
[28] Holdup Y Y
Attribute:
123456 7 8
PGM Option
ON Serv. req. AC Fail
Disabled
Y
TLM Fault
Disabled
Y
FTC
Disabled
Y
Zone Fault
Disabled
Y
Zone Tmp.
Disabled
Y
Zn. Low Bat.
Disabled
Y
Loss of Clock
Disabled
Y
OFF Disabled
[09] System Trouble Y
ON Burg. Evnt. Fire Evnt. Panic Evnt. Med. Evnt. Supv. Evnt. Priority Evnt. Holdup Evnt. Follows Timer*
OFF Disabled Disabled Disabled Disabled Disabled Disabled Disabled Latched
[10] System Event YYYYYYY N
*If attribute [8] is turned ON, attributes [1-7] must also be turned ON.
ON: Follows Zone Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8
OFF: Doesn’t Follow Zone
[29] Zone Follower NNNNNNN N

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the DSC PowerSeries PC585 and is the answer not in the manual?

DSC PowerSeries PC585 Specifications

General IconGeneral
Partitions1
CommunicatorBuilt-in
Keypads Supported8
PGM Outputs2
Power Supply16.5VAC
Battery Backup12VDC, 4AH
Operating Temperature0°C to 49°C (32°F to 120°F)
HumidityUp to 85% non-condensing
Zones8

Related product manuals