E Instruments E4500-S - Use with External Power Pack

144 pages

To Next Page

To Previous Page

K000000000EJ 023826A0 100714

7.3.2 Use with external power pack

The instrument can work with the batteries fully discharged by connecting the external power pack provided.

THE POWER SUPPLY/BATTERY CHARGER IS A SWITCHING TYPE ONE.

THE APPLICABLE INPUT VOLTAGE RANGES BETWEEN 90Vac AND 264Vac.

INPUT FREQUENCY: 50-60Hz.

THE LOW VOLTAGE OUTPUT IS 5 VOLT WITH AN OUTPUT CURRENT GREATER THAN

1.5A.

LOW VOLTAGE POWER CONNECTOR: A-TYPE USB CONNECTOR + CONNECTION CABLE WITH B-

TYPE PLUG.

Main Page

Default Chapter3
- Table of Contents3
Important Information7
- Introduction7
- Safety Warnings7
Safety8
- Intended Use of the Product8
- Improper Use of the Product8
Working Principle9
- Measuring Sensors9
Description of the Product10
- General Description of the Combustion Analyzer10
- General Characteristics of the Combustion Analyzer10
- Description of the Components of the Combustion Analyzer12
Main Configurations15
Technical Specifications16
- Measurement and Accuracy Ranges17
Startup18
- Preliminary Operations18
- Warnings18
- Power Supply of the Analyzer18
  - Checking and Replacing the Batteries18
  - Use with External Power Pack19
- Connection Diagram20
Power on - off23
- Starting the Device23
Configuration24
- Configuration Menu24
- Analysis Menu25
- Instrument Menu34
- Configuration=>Operator41
- Configuration=>Alarm43
- Information Menu44
- Configuration=>Diagnostic48
- Configuration=>Language58
- Configuration=>Restore59
Memory60
- Memory Menu60
- Memory=>Save62
- Memory=>Average64
- Memory Select65
  - Memory=>Memory Recall66
- Memory Data Logger69
- Memory=>Delete70
  - Memory=>Delete=>Single71
  - Memory=>Delete=>All72
- Memory=>Usage73
Print74
- Print Menu74
- Print=>Report75
- Print=>Configuration76
- Print=>Test77
- Print=>Header78
- Print=>Printer80
  - Print=>Printer=>Pairing81
- Print=>Measures List83
Measurements85
- Measurements Menu85
- Measurements Draft87
- Measurements Smoke88
- Measurements Ambient CO89
- Measurements Temperature90
- Measurements Pressure91
- Measurements=>Tightness Test92
  - Connection of the Tool Tightness Test Kit92
- Measurements=>Tightness Test=>New System93
  - Performing Tightness Test According to UNI 712995
- Measurements=>Tightness Test=>Existing System98
  - Configuration of Tightness Test According to UNI 11137102
  - Performing Tightness Test According to UNI 11137106
- Measurements=>Tightness Test=>Results of the Tightness Test108
Combustion Analysis110
- Startup and Auto-Calibration of the Device110
- Inserting the Probe in the Chimney110
- Combustion Analysis111
- End of Analysis111
- Combustion Analysis - Preliminary Operations112
- Combustion Analysis - Manual Mode114
- Combustion Analysis - UNI 10389 Mode116
- Combustion Analysis - Bimschv Mode117
- Combustion Analysis - Data Logger Mode118
Sensors119
- Sensors Arrangement119
- Sensor Types and Relevant Positioning119
- Gas Sensors Life120
- Table of Gas Sensor Life120
- Expandability to 4 Sensors121
- Cxhy Sensor for Measurement of the Unburned Hydrocarbons122
- Installing the Cxhy Sensor122
- CO Sensor for Carbon Dioxide Measurement in Combustion Processes123
- Installing the CO123
  - Sensor123
- Maintenance124
Troubleshooting131
- Troubleshooting Guide131
Spare Parts and Technical Assistance133
- Spare Parts133
- Accessories133
- Service Centers133
ANNEX a - Analysis Report Examples134
ANNEX B - Coefficients of the Fuels and Formulas137
ANNEX C - Declaration of Conformity139

E Instruments E4500-S - Use with External Power Pack

Table of Contents

Related product manuals