To Next PageTo Next PageWhat to do if the sound is dead on my Eclipse CD5425 Car Receiver?
If the sound from your Eclipse Car Receiver is dead or weak: * Make sure the volume isn't too low. * Deactivate the muting (MUTE) function. * Adjust the fader and balance controls. If the issue continues, it may be due to broken audio-signal wiring or a faulty speaker, which should be inspected by your dealer.
Why does my Eclipse Car Receiver only receive static noise?
If your Eclipse Car Receiver is not picking up any stations, or you're only getting static noise, try the following: * Extend the antenna. * Make sure the tuner is correctly tuned to a station. * If you're driving outside the service area of your preset stations, tune to a local station. Note that there may be no local stations servicing your current area. * Avoid operating other equipment like computers or mobile phones while using the receiver. If the problem persists, it could be a loose or disconnected antenna cable, a bad antenna, which should be inspected by your authorized Eclipse retailer.
How to fix an Eclipse Car Receiver remote control that is not working?
If the remote control for your Eclipse Car Receiver isn't working: * Replace the battery. * Ensure the battery is installed with the correct polarity. * Make sure direct sunlight isn't hitting the remote control light receptor; use the remote closer to the receptor. If the remote still doesn’t work, it may be malfunctioning and should be checked by your dealer.
Why won't my Eclipse Car Receiver power on?
If your Eclipse Car Receiver is not turning on, it could be due to too many electrical items installed, causing a lack of power. It is recommended to have your dealer check the problem. Other possible causes are a run-down car battery or broken power or interconnection wiring, which also require a dealer's inspection.
What to do if my Eclipse CD5425 sound skips?
If your Eclipse Car Receiver is skipping, intermittent, or of poor quality: * Try another disc and avoid playing damaged discs. * Clean the disc. * Avoid playback while driving over rough surfaces. For issues related to player mounting angle or looseness, have your dealer check it out.
Why does my Eclipse Car Receiver keep deleting memory?
If the frequencies or titles set in memory on your Eclipse Car Receiver are deleted, and the car battery has been disconnected for repair, you should reenter them into memory. If there are too many electrical items installed, causing a lack of available power, have your dealer check the problem. Other probable causes include a run-down car battery, broken power or interconnection wiring, which also require a dealer's inspection.
What to do if my Eclipse Car Receiver won't accept or eject discs?
If the disc cannot be inserted into your Eclipse Car Receiver, or is ejected immediately after insertion, or cannot be ejected or changed: * Do not apply labels or seals to the disc. * Try inserting another disc. Remove any burrs from the disc. Do not use a deformed or damaged disc.
How to fix 'No Disc Loaded' error on my Eclipse Car Receiver?
If your Eclipse Car Receiver displays 'NO DISC LOADED', load a music disc in the magazine.
What if my Eclipse Car Receiver says 'Discs are dirty'?
If your Eclipse Car Receiver displays that discs are dirty or damaged, verify the disc is clean and properly oriented.
What to do if CD player fails mechanically on Eclipse CD5425?
If your Eclipse Car Receiver's CD player and CD changer fails mechanically, go through the magazine removal procedure.
General| Bluetooth | No |
|---|---|
| USB Port | No |
| Display Type | LCD |
| Type | CD Receiver |
| DIN Size | Single DIN |
| Detachable Face | Yes |
| RMS Power Output | 22W x 4 |
| Channels | 4 |
| CD Player | Yes |
| Remote Control | Yes |
| Tuner | FM/AM |
| Aux Input | Yes |
| EQ Bands | 3-Band |
Essential warnings, caution definitions, and operational safety rules.
Guidelines for safe installation, wiring, and power connection.
Rules for safe driving, unit usage, and environmental considerations.
Covers power management, CD/Tuner playback, and audio adjustments.
Explains and configures crossover, phase, and equalizer settings.
