Eclipse EA500 User Manual

CHAPTER - 34 HIGHLIGHTS
(Summary of Changes)
Revision No. TR34-21 Sep 30/20
TO: HOLDERS OF THE AIRCRAFT MAINTENANCE MANUAL (06-117751)
Pages that have been added or revised are summarized below. Remove and insert the affected
pages as listed, and enter the above revision number with issue date into the Record of Revisions
sheet.
This Temporary Revision incorporates and supersedes previously released temporary
revisions for the chapters listed below.
Do not remove this page. Keep it in place as a record of previous changes.
CH/SE/SU
Page Block No. Description of Change
34-10-00
PgBlk 501
Adjustment / Test - Added Standby Pitot/Static Verification with Standby
Display Unit (SDU).
34-10-10
PgBlk 401-Rem
(C)
Added MB 500-34-028 to effectivity for Pitot/AOA Probe auxiliary heaters -
Removal - Config C.
34-10-10
PgBlk 401-Inst
(C)
Added MB 500-34-028 to effectivity for Pitot/AOA Probe auxiliary heaters -
Installation - Config C.
34-40-50
PgBlk 1 (A) Description and Operation – Config A. Corrected effectivity.
34-40-50
PgBlk 1 (B)
Description and Operation – Config B. Added configuration B – POST SB
500-31-024.
34-40-50
PgBlk 501 (A) Adjustment/Test – Config A. Corrected effectivity.
34-40-50
PgBlk 501 (B)
Adjustment/Test – Config B. Added configuration for Stormscope lightning
strike test post SB 500-31-024.
34-50-10
PgBlk 1 (B)
Description and Operation - Revised Effectivity (ALL POST MB
500-31-018). Revised Description.
34-50-10
PgBlk 201 (A)
Description and Operation - Revised Effectivity (ALL POST MB
500-31-018). Updated for ADS-B Out – Config A.
34-50-10
PgBlk 201 (B) Added GPS 3 (GDL 88) Maintenance Practices – Config B.
34-50-10
PgBlk 501 (C) Adjustment/Test for GPS Units – Config C.
34-50-11
PgBlk 401-Rem
(C) Added GPS 3 (GDL 88) Unit Removal procedure.
EA500 Aircraft Maintenance Manual — 06-117751
Temporary Revision No. 34-21
34-HIGHLIGHTS
Page 1
Sep 30/20
© 2020 Eclipse Aerospace, Inc.

Eclipse EA500 Specifications

General

Manufacturer	Eclipse Aerospace
Model	EA500
Type	Very Light Jet
Crew	1-2
Passenger Capacity	4-5
Powerplant	2 × Pratt & Whitney Canada PW610F turbofans
Thrust per Engine	900 lbf (4.0 kN)
Service Ceiling	41, 000 ft (12, 500 m)
Avionics	Avio NG
Height	11 ft
Maximum Speed	694 km/h
Range	1, 125 nmi (2, 083 km)

Summary

Flight Environment Data - Adjustment/Test

General

Provides an overview of the adjustment and test procedures for flight environment data components.

Equipment and Materials

Lists special tools and equipment required for the flight environment data adjustment/test procedures.

Job Set-Up

Details the necessary preparation steps before performing the flight environment data adjustment/test.

Procedure – Upper Over Fin Fairing – NOT INSTALLED

Step-by-step instructions for performing the adjustment/test when the upper over fin fairing is not installed.

Initial System Test

Performs initial checks on the Stormscope system to verify proper display and functionality.

Cardinal Bearings Test

Tests the accuracy of bearing display for the Stormscope system at various cardinal points.

Heading Input Check

Verifies the aircraft's heading input affects the Stormscope display correctly.

Procedure – Upper Over Fin Fairing – INSTALLED

Step-by-step instructions for performing the adjustment/test when the upper over fin fairing is installed.

Stormscope - Description and Operation

General

Introduces the Lightning Detection System (LDS) and its trademark name, Stormscope.

Description

Describes the Stormscope system's detection of electrical discharges and its display on the GPS 400W.

Operation

Outlines the functions provided by the Stormscope system, including display modes and operation.

Stormscope - Description and Operation (Config B)

General

Introduces the Lightning Detection System (LDS) and its trademark name, Stormscope.

Description

Describes the Stormscope system's detection of electrical discharges and its display on the PFD.

Operation

Outlines the functions provided by the Stormscope system, including display modes and operation.

Stormscope - Adjustment/Test

General

Provides an overview of the adjustment and test procedures for the Lightning Detection System (LDS).

Equipment and Materials

Lists special tools and equipment required for the Stormscope adjustment/test.

Job Set-Up

Details the necessary preparation steps before performing the Stormscope adjustment/test.

GPS 3 - Maintenance Practices

General

Provides general information for configuring the GPS 3 (GDL 88) unit for use on the Eclipse Model 500 aircraft.

Equipment and Materials

Lists special tools and equipment required for configuring the GPS 3 (GDL 88) unit.

Job Set-Up

Details the necessary preparation steps for configuring the GPS 3 (GDL 88) unit.

Procedure

Provides the step-by-step procedure for configuring the GPS 3 (GDL 88) unit.

GPS - Adjustment/Test

General

Provides procedures for adjusting and testing GPS 1 and GPS 2 components.

Job Set-Up

Details the necessary preparation steps for GPS adjustment and testing.

MFD Set-Up

Configures the Multi-Function Display (MFD) for GPS adjustment and testing.

GPS 1 Test

Performs adjustment and test procedures specifically for GPS 1.

GPS 3 - Removal

General

Provides procedures for removing the Global Positioning System (GPS 3) unit.

Job Set-Up

Details the necessary preparation steps for GPS 3 unit removal.

Procedure

Provides the step-by-step procedure for removing the GPS 3 unit.

GPS - Removal

General

Provides procedures for removing the Global Positioning System/Wide Area Augmentation System (GPS/WAAS) sensors.

Job Set-Up

Details the necessary preparation steps for GPS/WAAS sensor removal.

Procedure

Provides the step-by-step procedure for removing the GPS/WAAS sensors.

GPS - Installation

General

Provides procedures for installing the Global Positioning System/Wide Area Augmentation System (GPS/WAAS) Garmin GPS 400W Navigator.

Equipment and Materials

Lists special tools and equipment required for GPS 400W installation.

Job Set-Up

Details the necessary preparation steps for GPS 400W installation.

Procedure

Provides the step-by-step procedure for installing the GPS 400W unit.

GPS 3 - Installation

General

Provides procedures for installing the Global Positioning System (GPS 3) unit.

Job Set-Up

Details the necessary preparation steps for GPS 3 installation.

Procedure

Provides the step-by-step procedure for installing the GPS 3 unit.

GPS - Installation (Config D)

General

Provides procedures for installing the Global Positioning System/Wide Area Augmentation System (GPS/WAAS) sensors.

Job Set-Up

Details the necessary preparation steps for GPS/WAAS sensor installation.

Procedure

Provides the step-by-step procedure for installing the GPS/WAAS sensors.

GPS 3 Mount - Removal

General

Provides procedures for removing the Global Positioning System (GPS 3) mount.

Job Set-Up

Details the necessary preparation steps for GPS 3 mount removal.

Procedure

Provides the step-by-step procedure for removing the GPS 3 mount.

GPS 3 Mount - Installation

General

Provides procedures for installing the Global Positioning System (GPS 3) mount.

Job Set-Up

Details the necessary preparation steps for GPS 3 mount installation.

Procedure

Provides the step-by-step procedure for installing the GPS 3 mount.

GPS 2 Antenna Splitter - Removal

General

Provides procedures for removing the GPS 2 Antenna Splitter.

Job Set-Up

Details the necessary preparation steps for GPS 2 Antenna Splitter removal.

Procedure

Provides the step-by-step procedure for removing the GPS 2 Antenna Splitter.

GPS 2 Antenna Splitter - Installation

General

Provides procedures for installing the GPS 2 Antenna Splitter.

Job Set-Up

Details the necessary preparation steps for GPS 2 Antenna Splitter installation.

Procedure

Provides the step-by-step procedure for installing the GPS 2 Antenna Splitter.

Transponder - Description and Operation

General

Introduces the Standard and Optional Diversity Transponder Systems.

Description

Describes the components of the Standard and Optional Diversity Transponder Systems.

Operation

Explains the operation of the Standard and Optional Diversity Transponder Systems.

Transponder - Description and Operation (Config D)

General

Introduces the Standard and Optional Diversity Transponder Systems and ADS-B Function.

Description

Describes the components of the Standard and Optional Diversity Transponder Systems.

Operation

Explains the operation of the Standard and Optional Diversity Transponder Systems, including ADS-B.

Transponder with ADS-B Out – Maintenance Practices

General

Provides instructions for configuring the Transponder for ADS-B Out on the Eclipse 500 aircraft.

Equipment and Materials

Lists special tools and equipment required for transponder configuration for ADS-B Out.

Job Set-Up

Details the necessary preparation steps for transponder configuration for ADS-B Out.

Transponder - Adjustment/Test

General

Provides procedures for the adjustment/test of transponder components.

Equipment and Materials

Lists special tools and equipment for transponder adjustment/test.

Transponder - Adjustment/Test (Config B)

General

Provides procedures for adjustment/test of Dual Standard and Dual Diversity Transponder Systems.

Equipment and Materials

Lists special tools and equipment for transponder adjustment/test.

Transponder - Adjustment/Test (Config C)

General

Provides procedures for adjustment/test of Dual Standard and Dual Diversity Transponder Systems.

Equipment and Materials

Lists special tools and equipment for transponder adjustment/test.

ADS-B Out with GPS 3 - Description and Operation

Introduction

Introduces the Automatic Dependent Surveillance – Broadcast Out (ADS-B Out) system.

Description

Describes the components of the ADS-B Out system with Dual Transponder System.

Operation

Explains the operation of the ADS-B OUT system utilizing Extended Squitter and GPS 3.

ADS-B - Adjustment/Test

General

Provides procedures to perform the adjustment/test of the ADS-B.

Equipment and Materials

Lists special tools and equipment for ADS-B adjustment/test.

Job Set-Up with UC-584 Antenna Couplers

Details the necessary preparation steps for ADS-B adjustment/test using UC-584 Antenna Couplers.

Transponder - Installation

General

Provides procedures to install the transponder.

Job Set-Up

Details the necessary preparation steps for transponder installation.

Procedure

Provides the step-by-step procedure for installing the transponder.

Transponder Antenna Relay - Installation

General

Provides procedures to install the transponder antenna relay(s).

Job Set-Up

Details the necessary preparation steps for transponder antenna relay installation.

Procedure

Provides the step-by-step procedure for installing the transponder antenna relay(s).