Why is the drill not rotating on my Ellis 9400 Power Tool?
If the drill is not rotating on your Ellis Power Tool, the taper on the chuck might be slipping in the spindle. Remove any grease and oil from inside the taper bore in the spindle and outside of the taper on the chuck using mineral spirits.
Why is the spindle not moving up on my Ellis Power Tool?
If the spindle isn't moving up on your Ellis Power Tool, the return spring or Pawl Assembly might be broken. Replace the spiral-spring #8429 or replace Pawl Assembly #8380.
What to do if the hole depth is not correct using my Ellis 9400?
If the hole depth isn't correct with your Ellis Power Tool, it may be because: * The depth dial isn't clamped; tighten the dial lock. * The worm gear or quill is worn; replace the gear.
Why is the spindle not rotating in the correct rotation on my Ellis Power Tool?
If the spindle isn't rotating correctly on your Ellis Power Tool, the switch on the VS Control Box might be in the wrong position. Use the forward switch for standard drilling and cutting, and the reverse switch to retract a tap or when tapping for left-hand threads.
What to do if my Ellis 9400 has no power feed?
If your Ellis Power Tool has no power feed, consider these potential causes: * A worn worm gear: Replace the worm gear. * A faulty overload protection device: Tighten the springs with adjustment screws. * A worn pawl clutch: Replace the Hub and Pawl Assembly #8380. * A sliding feed belt: Tighten the belt. * Feed Handles do not move sideways: Loosen thumbscrew #8383.
What causes excessive drill run out in my Ellis 9400 Power Tool?
Excessive drill run out in your Ellis Power Tool could be caused by: * A bent drill; replace the drill. * Chuck jaws not clamping evenly; install the drill correctly. * Worn spindle bearings; replace the ball bearings.
How to troubleshoot noisy operation in my Ellis 9400?
Noisy operation in your Ellis Power Tool can stem from several issues: * Incorrect belt tension: Adjust the tension. * Loose spindle or motor pulley: Tighten the set screw #8081. * Belt is too tight: Reduce belt tension. * Worn spindle bearing: Replace the spindle ball bearing.
Why is my Ellis 9400 drill bit smoking or burnt?
If your Ellis Power Tool drill bit is smoking or burnt, it could be due to several reasons: * The drill bit needs lubrication, so lubricate with cutting fluid. * The drill might be running in reverse; change the motor rotation. * The drill bit may be dull; sharpen or replace it. * The speed might be incorrect; adjust the speed accordingly. * Chips may not be coming out of the hole; retract the drill bit frequently to clear them out.
General information about the drill press features, power, and factory presets.
Instructions for proper operation and maintenance before initial use.
Safety warnings and requirements for connecting the drill press to a power source.
Essential safety rules to follow while operating the drill press.
Explanation and identification of safety labels found on the machine.
Critical warnings and instructions regarding the Variable Speed Control Box.
Specific precautions related to personal attire when operating the equipment.
Technical details, dimensions, and capacities of the drill press.
Electrical data and performance characteristics of the drill press motor.
Step-by-step guide for setting up and using the Variable Speed Control Box.
Important note and warning about stalling the motor and potential warranty issues.
Procedure for adjusting the torque range using the shift handle and range knob.
Overview of available spindle speed ranges and their suitability for different tasks.
Explanation of spindle speed control and a comprehensive speed chart.
Explanation of how to operate both power feed and manual feed mechanisms.
Instructions for setting the desired depth of drilled holes.
Explanation of the overload clutch, its purpose, and adjustment.
Instructions for mounting the Morse Taper #3 arbor and drill chuck.
Procedure for safely removing the drill chuck and arbor using a drift key.
Guidance on selecting appropriate spindle speeds for drilling and tapping materials.
Proper technique for securing drill bits and taps within the chuck.
How to adjust the drill press worktable's position and orientation.
Detailed list of all parts comprising the head assembly of the drill press.
Detailed list of all parts comprising the worktable and base assembly.
Chart identifying the location, type, size, and quantity of bearings.
Recommended lubrication points, lubricant type, and service frequency.
General cleaning, oiling, and inspection tasks for maintaining the machine.
Specifications and description of the optional milling table attachment.
Details and specifications for the drill chuck and arbor accessory.
Specifications and description of the 6.25-inch drill press vise.
Description of the polycarbonate chuck guard for operator safety.
Specifications for T-slot bolts used for securing workpieces.
General| Brand | Ellis |
|---|---|
| Model | 9400 |
| Category | Power Tool |
| Language | English |
To Next Page
