To Next PageTo Next Page
What does error code F162 mean on Endress+Hauser Deltabar FMD72 and how to fix it?
The error code F162 on your Endress+Hauser Measuring Instruments may indicate a defective sensor module (master) or electromagnetic effects outside the permitted range. To address this, check the sensor cable and replace the sensor.
What does error code F282 mean on Endress+Hauser Deltabar FMD72 and how to resolve it?
The error code F282 on your Endress+Hauser Measuring Instruments indicates a fault in the main electronics. To resolve this, try replacing the electronics or restarting the device.
What does error code F081 mean on Endress+Hauser Deltabar FMD72 Measuring Instruments and how to troubleshoot it?
Error code F081 on Endress+Hauser Measuring Instruments can be triggered by electromagnetic effects exceeding specifications, a defective sensor module, or a disconnected cable between the sensor module and main electronics. To resolve this, check the sensor cable or perform a reset.
What does error code F062 mean on Endress+Hauser Deltabar FMD72 and how can I resolve it?
The error code F062 on your Endress+Hauser Measuring Instruments can be caused by several factors, including electromagnetic effects exceeding specifications, a defective sensor module, or a disconnected cable between the sensor module and main electronics. You can try replacing the electronics or checking the sensor module cable.
What does error code F261 mean on Endress+Hauser Measuring Instruments and how to fix it?
The error code F261 on your Endress+Hauser Measuring Instruments indicates a fault related to the main electronics or the sensor module. To address this issue, try restarting the device or replacing the electronics.
How to fix HART communication not working on Endress+Hauser Measuring Instruments?
If HART communication is not working on your Endress+Hauser Measuring Instruments, it could be due to a few reasons. First, check if the communication resistor (250 ?) is missing or incorrectly installed, and install it correctly. Also, verify that the Commubox is properly connected and set the Commubox selector switch to "HART".
What to do if Endress+Hauser Deltabar FMD72 Measuring Instruments device measures incorrectly?
If your Endress+Hauser Measuring Instruments device is measuring incorrectly, the most likely cause is a configuration error. To fix this, check and correct the parameter configuration.
Why is there no display on my Endress+Hauser Deltabar FMD72?
If there is no display on your Endress+Hauser Measuring Instruments, it could be due to several reasons. First, the onsite display might be set too bright or too dark. To resolve this, try setting the local display brighter by simultaneously pressing the indicated buttons or darker by pressing the other indicated buttons. Another potential cause is a connector for the local display that is not properly connected, make sure the connector is properly connected. Finally, the onsite display could be defective, in which case it needs to be replaced.
What to do if Endress+Hauser Deltabar FMD72 device is not responding?
If your Endress+Hauser Measuring Instruments device isn't responding, there are a few things you can check: * First, ensure that the supply voltage matches what's specified on the device's nameplate and apply the correct voltage. * Next, verify that the supply voltage has the correct polarity; if it doesn't, reverse the polarity. * Finally, check the connection of the cables to the terminals, and correct them if necessary.
What to do if the output current is less than 3.6 mA on my Endress+Hauser Measuring Instruments?
If the output current is less than 3.6 mA on your Endress+Hauser Measuring Instruments, consider the following: * The signal line may not be wired correctly. Check the wiring. * The electronics unit may be defective. Replace the electronics.
General| Device Type | Differential pressure transmitter |
|---|---|
| Application | Level measurement, flow measurement |
| Measuring Range | Up to 400 bar |
| Process Temperature | -40 to 125 °C |
| Output Signal | 4-20 mA HART, PROFIBUS PA, FOUNDATION Fieldbus |
| Housing | Aluminum or stainless steel |
| Communication | HART, PROFIBUS PA, FOUNDATION Fieldbus |
| Power Supply | 10.5 to 45 V DC |
| Protection Class | IP66 |
| Material | Stainless steel |
| Approvals/Certifications | ATEX, IECEx |
| Process Connection | Flanged, threaded |
