Endress+Hauser Gammapilot FMG50 User Manual (English)

Other manuals for Endress+Hauser Gammapilot FMG50

Operating Instructions108 pages

Technical Information48 pages

Questions and Answers:

A
adrianwardAug 22, 2025
Why is login via SmartBlue not possible for Endress+Hauser Measuring Instruments?
- V
  vincentwatersAug 22, 2025
  Login via SmartBlue might be impossible due to several reasons. The Bluetooth function may be disabled on your smartphone or tablet, or the Bluetooth function of the sensor itself might be disabled, requiring a recovery sequence. Ensure that the HistoROM is attached. Only one point-to-point connection can be established between a sensor and a smartphone or tablet. If the device is being used for the first time, use the device serial number as the initial password, paying attention to upper and lower case.
I
igutierrezAug 23, 2025
What to do if the Endress+Hauser Gammapilot FMG50 Measuring Instruments device cannot be operated via SmartBlue?
- C
  Cassandra BrownAug 23, 2025
  If the device cannot be operated via SmartBlue, ensure that you are entering the correct password. If the password has been forgotten, contact Endress+Hauser Service. In case the sensor temperature is too high (over 60 °C or 140 °F) due to ambient temperature, Bluetooth communication may be disabled. Shield the device, isolate it, and cool it down if necessary.
L
Latoya HoweAug 25, 2025
What to do if Endress+Hauser Gammapilot FMG50 Measuring Instruments device is visible in live list but cannot be accessed via SmartBlue on Android?
- T
  tranchristopherAug 26, 2025
  If the device is visible in the live list but cannot be accessed via SmartBlue on an Android device, ensure that the location function is permitted for the app. Some Android versions require GPS or positioning function to be activated. Close the app fully, restart it, and enable the positioning function for the app.
A
Alicia MeyersAug 27, 2025
What to do if pulse rate is too low with empty vessel for Endress+Hauser Gammapilot FMG50?
- M
  Michael WintersAug 27, 2025
  If the pulse rate is too low with an empty vessel, the radiation source might be switched off; switch it on at the source container. The source housing might be incorrectly aligned; realign the angle of emission. Buildup in the vessel could be the cause; clean the vessel or recalibrate if the buildup is stable. Also, fittings or pressure in the vessel might not have been considered in the activity calculation; recalculate activity and change the radiation source if required. Check if there is no radiation source in the source container; load radiation source. The radiation source may be too weak; use a source with higher activity. If a modulator is used, make sure it is mounted correctly. If a collimator is used, ensure correct alignment of the radiation entry window.
H
howardstevenAug 27, 2025
Why is pulse rate too high with empty vessel for Endress+Hauser Measuring Instruments?
- D
  Derek RussellAug 28, 2025
  If the pulse rate is too high with an empty vessel, the activity might be too high. Attenuate radiation, for example, by mounting a steel plate in front of the source container, or replace the radiation source. External radiation sources might be present; shield off if possible and repeat calibration without the external radiation source.
K
Kelly WilliamsAug 29, 2025
Why is pulse rate too high with full vessel for Endress+Hauser Measuring Instruments?
- G
  Gary SheaAug 29, 2025
  If the pulse rate is too high with a full vessel, external radiation sources might be present. Shield off the external radiation if possible and repeat calibration without the external radiation source.
E
Emma AllenAug 30, 2025
Why TAG in SmartBlue and HART do not match for Endress+Hauser Gammapilot FMG50?
- J
  John FieldsAug 30, 2025
  The device ID (TAG) is transferred to the live list via Bluetooth® to facilitate device identification. The tag is abbreviated in the middle since the HART tag can be up to 32 characters long but Bluetooth® can only use 29 characters as the device name.
S
Sheila GriffinAug 31, 2025
What to do if the Endress+Hauser Measuring Instruments sensor is defective?
- S
  Sonya BlankenshipSep 1, 2025
  Replace sensor electronics. Restart device. Contact service.
J
Jesse GomezSep 2, 2025
What to do if the Endress+Hauser Gammapilot FMG50 Measuring Instruments sensor connection is faulty?
- J
  Jennifer BurtonSep 2, 2025
  Check sensor connection.
A
andrewsanchezSep 3, 2025
What to do if the Endress+Hauser Gammapilot FMG50 pulse rate is out of range?
- V
  Vicki BlackSep 3, 2025
  Check process conditions. Check environmental conditions. Replace device.

Endress+Hauser Gammapilot FMG50 Specifications

General

Measuring Principle	Gamma radiation
Housing Material	Aluminum or Stainless steel
Application	Level measurement in liquids and bulk solids
Process Temperature	-40 to +80 °C
Process Pressure	Up to 40 bar
Output Signal	4-20 mA, HART
Protection Class	IP66
Communication	HART
Certificates/Approvals	ATEX, IECEx
Ambient Temperature	-40 to +60 °C (-40 to +140 °F)